Electronics Forum: problem home position stf100s (Page 1 of 4)

Wrote some software at home ................... (plug)

Electronics Forum | Wed May 12 23:33:04 EDT 1999 | Matt

WARNING: This is a plug. I have read post on this site where the question is raised: "My machine can do 80 units per hour, but I am only getting 35 - WHY?" Well I have written w95/database code that reads FUJI output files (CPII,CPII,IP2 etc) and d

zevatech 570 Driver Error KNOCK position E7018

Electronics Forum | Thu Mar 30 08:04:56 EDT 2023 | hub

Hello, I'm looking for zevatech (juki) 570 owner that could help me to resolve my problem. I had the following error that occure just before (or sometime a few after) homing the machine : "E7018:Driver Error KNOCK position error ". Previsously I had

Re: Wrote some software at home ................... (plug)

Electronics Forum | Thu May 13 00:34:49 EDT 1999 | Jeff Sanchez

| WARNING: This is a plug. | | I have read post on this site where the question is raised: "My machine can do 80 units per hour, but I am only getting 35 - WHY?" | | Well I have written w95/database code that reads FUJI output files (CPII,CPII,IP2

Re: Wrote some software at home ................... (plug)

Electronics Forum | Thu May 13 09:41:25 EDT 1999 | Chrys Shea

| | WARNING: This is a plug. | | | | I have read post on this site where the question is raised: "My machine can do 80 units per hour, but I am only getting 35 - WHY?" | | | | Well I have written w95/database code that reads FUJI output files (CPII

Re: Wrote some software at home ................... (plug)

Electronics Forum | Thu May 13 21:22:27 EDT 1999 | Matt

| | | WARNING: This is a plug. | | | | | | I have read post on this site where the question is raised: "My machine can do 80 units per hour, but I am only getting 35 - WHY?" | | | | | | Well I have written w95/database code that reads FUJI output f

Quad 4C place problem

Electronics Forum | Wed Mar 31 06:08:45 EDT 2010 | miroyu

Hi everyone ! I started to program quad 4C for the first time and have some problems. First, board detection LED and proximity Led (on the front panel) are not lightning whatever I do! Second problem is I teach machine board size, nozzle locations

DEK 265 Horizon Servo Following Error

Electronics Forum | Fri Jan 05 12:02:28 EST 2018 | ilavu

Camera works fine from home to ref. position to fiducial1 and 2. Problem shows up from home to board stop. AC voltage between AC1 and AC2 is 41.7 and during move it drops to 41.5.

Problem with y-axis Yamaha84 SMT mounter

Electronics Forum | Tue Oct 25 22:50:16 EDT 2005 | KEN

What is the (initial position) ratio of pulse counts to home encoder pulse (relative to the home sensor). It should be 50% +/- 15% Run this test several times in between a warm up. I bet your numbers are all over the place. I bet you have a loos

contact 3av head homing errors

Electronics Forum | Fri Sep 24 16:01:07 EDT 2010 | dougt

I remember this problem but can't remember exactly what the reason was. It might have been the wrong pullup resistor on the MEI interface board used for the home photo on the y axis. You are right, after a couple hours the machine would work fine.

MPM Accuflex problems and errors

Electronics Forum | Tue Mar 30 06:27:22 EDT 2010 | ristikas

It happens on the middle of the stecil cleaning. The camera and the cleaner will stay under stencil in half way back. Then machine asking the initate the motors. If to press initate then the pcb stopper will hit the rails. Usually we move camera and

  1 2 3 4 Next

problem home position stf100s searches for Companies, Equipment, Machines, Suppliers & Information

PCB Handling with CE

High Throughput Reflow Oven
convection smt reflow ovens

Benchtop Fluid Dispenser
thru hole soldering and selective soldering needs

Component Placement 101 Training Course
2024 Eptac IPC Certification Training Schedule

Software programs for SMT placement and AOI Inspection machines from CAD or Gerber.
SMT feeders

World's Best Reflow Oven Customizable for Unique Applications