Electronics Forum: qfp and float (Page 1 of 10)

qfp and soic joint Problem

Electronics Forum | Tue Apr 11 10:30:46 EDT 2000 | Jeremy Smith

I am having a problem with some joints on a 100 pin pqfp and few different soics on one particular board. When viewed a 8x with a "Mantis" inspection scope the joints look as though they wetted to the ic leg but when probed the leg will pop loose.

Re: qfp and soic joint Problem

Electronics Forum | Mon Apr 17 19:30:27 EDT 2000 | Boca

All of the above is good stuff. To add, I have seen this several times if the assembly is wavesoldered. Heat from the wave can partially reflow the top side SM solder joints and weaken them. To test, check joint strength before wave and then after

Re: qfp and soic joint Problem

Electronics Forum | Tue Apr 11 14:59:05 EDT 2000 | Glenn Robertson

Jeremy - What's the process flow on these modules? Are they wave soldered? What is the board finish (ENG, HASL, etc.)? Glenn Robertson

Re: qfp and soic joint Problem

Electronics Forum | Tue Apr 11 16:42:56 EDT 2000 | Chad Notebaert

I�m thinking �Poor intermatallic� It could be a few things. Lets start at the beginning. -Is your paste a 63/37 mixture? -Have you monitored you screen printing, Verify Solder deposition, Are you getting enough paste? -You say the solder looks like i

Re: qfp and soic joint Problem

Electronics Forum | Tue Apr 11 20:26:16 EDT 2000 | Dave F

Jeremy: Parts assembler make leads of either Alloy 42 (Invar, whatever) or copper. The solderability of these leads are protected with eutectic or non-eutectic tin/lead solder, palladium or some palladium alloy, or gold. Cuppla things to consider:

J-STD-002 and -003 solderability testing...

Electronics Forum | Sat Jun 30 11:03:29 EDT 2001 | davef

Nice to have you back on SMTnet. Some of the newer folk have missed-out on the solid contributions you�ve made to the Forum. The chicken wire cleaning basket was a classic!!! [It�s a shame that the folk at SMTnet can�t recover those files.] We bu

WSOL and solder pot

Electronics Forum | Wed Mar 12 12:28:52 EDT 2008 | operator

I recently witnessed a process in which the solder pot operator used Techspray WSOL water soluble masking to cover the areas around a connector that was to be soldered on the solder pot. He did not wait for the WSOL to cure. He soldered immediately.

Pick and Place Rivet

Electronics Forum | Tue Aug 12 14:49:26 EDT 2008 | awegener

I'm attempting to pick and place a small rivet onto our PCB. The rivet should be attached via reflow solder. The rivet will be used to create a sandwich, holding together a frame and additional circuit board in a package. This part is intended onl

BGA and PCB finishing

Electronics Forum | Tue Mar 14 05:02:35 EST 2000 | emmanuel

I am to implement PBGA, and i am looking for PCB surface finish informations. A lot of technical reports are specifing NiAu finishing because of flatness property. Because of leads shape, I though that BGA doesn't need flat pads like QFP. Is it false

BGA and PCB finishing

Electronics Forum | Tue Mar 14 05:02:35 EST 2000 | emmanuel

I am to implement PBGA, and i am looking for PCB surface finish informations. A lot of technical reports are specifing NiAu finishing because of flatness property. Because of leads shape, I though that BGA doesn't need flat pads like QFP. Is it false

  1 2 3 4 5 6 7 8 9 10 Next

qfp and float searches for Companies, Equipment, Machines, Suppliers & Information