Electronics Forum: qsa-30 program (Page 1 of 2)

Quad QSA 30 opinion wanted

Electronics Forum | Wed Sep 26 14:18:50 EDT 2012 | tank

Wondering how good the software is for the Quad QSA 30 is. Is it a pain to program? We have panels with 100 boards... 1500 parts, I hope you don't have to manually teach the whole panelized board. Any other info you can provide is welcome. We

Advice on used pick and place machine

Electronics Forum | Mon Oct 09 07:50:22 EDT 2006 | quad

We currently run two Quad IVC's (we are very pleased with them) and two Versatronics for simple small volume batch work. We now need an additional machine capable of placing components at least three times as quickly as a IVC. We don't do anything ve

Quad optimizer

Electronics Forum | Tue May 02 11:21:43 EDT 2000 | �ngelo Marques

We have some Quad (QSA-30) machines, and i get better results when i optimize a program manually of the one that when i utilize the optimizer of the machine. Somebody knows a better software, than i stop using a manually optimizer. Sory me English. �

Samsung Quad QSA 30

Electronics Forum | Sat Jul 07 11:45:26 EDT 2012 | btipcb

I purchased and am setting up a used QSA30. It has been a little frustrating but I finally have an almost program. The isse is that I can not generate a placement program because it says that the ANC is not registered. I can look at it on the sy

CAN'T OPEN ANC. invalid place position x

Electronics Forum | Sat Oct 24 23:26:43 EDT 2015 | thefinder

Hi. Have a problem with a QSA 30 machine. show me a error at the end of set up program. CAN'T ANC OPEN and then show me on the next row message. invalid place position x. if anyone has any suggestions please tell me.

QUAD QSA-30

Electronics Forum | Fri Sep 24 14:05:06 EDT 2004 | jsloot

Is there anyone using a QUAD QSA-30? I am experiencing problems with the Y axis drifting in the positive direction. This can occur anytime from a few minutes to several hours after the problem has been fixed. Fixed means recreating a program from scr

Quad QSA 30 opinion wanted

Electronics Forum | Wed Sep 26 15:04:09 EDT 2012 | kahrpr

The QSA30 is basically a Samsung CP40 with a few changes. For an older machine the programming is pretty good. it can do array boards and has an import feature for XY data. Tts been about 7 years since I ran one. Its a pretty solid machine.

Samsung Quad QSA 30

Electronics Forum | Mon Jul 09 12:36:43 EDT 2012 | bobpan

Once you optimize and you go into step program....the nozzles should be assigned to each placement. If it is not doing this....the optimizer is still not working the way that it should.

Samsung Quad QSA 30 Final setup

Electronics Forum | Mon Jul 09 18:29:19 EDT 2012 | btipcb

I have gotten to what I hope is the last step before I can start running product. However, I have and keep receiving an "Invalid Place Position X" error in three steps of the placement program. I have verified that the camera can indeed find these

Quad Machines? Good Points / Bad Points

Electronics Forum | Thu May 02 10:27:18 EDT 2002 | BTaylor

I have used Quad/ Now Tyco since the early 90s starting with the 4c then on to the QSA-30s, APS-1, and now the Meridian 1010. We have six machines in a very small area and place over 10 million components per month. As others have said the service is

  1 2 Next

qsa-30 program searches for Companies, Equipment, Machines, Suppliers & Information

Dual Lane Reflow Oven

Stencil Printing 101 Training Course


High Precision Fluid Dispensers
used smt parts china

High Speed Precision In-Line SPI System - Mirtec MS-11