Electronics Forum: quad 4c dip switch (Page 1 of 3)

quad 1000 error

Electronics Forum | Thu Jan 19 10:53:43 EST 2006 | bobpan

Walter, Read what i posted above about switching the dip switch 8 on dip 1. That will probably solve your problem but once again....make sure you write down all your machine settings because everything will be reset.

quad 1000 error

Electronics Forum | Mon Jun 13 19:07:57 EDT 2005 | bobpan

Mike, Right down all the settings you have for your machine (this may take a while). Also back up the programs you want to save. Now....if i can remember correctly.....when looking into the black computer box from the back of the machine...in your bo

Quad 4C power switch

Electronics Forum | Fri Aug 16 03:13:32 EDT 2013 | rollon65

Hi Marcelo. I have used 2 non EU model 4C machines since 2002 that do this almost every time from a cold switch on. My local Tyco tech guy said that they all do it. They are still going after 12 years. I have another EU machine that does the sam

Quad 4C power switch

Electronics Forum | Thu Sep 12 20:55:39 EDT 2013 | marcelorotofrance

My own unit has an internal transformer also. It has multiple secondaries, and a divided primary which can be configured to the required voltage by changing jumpers. Best regards.

Quad 4C power switch

Electronics Forum | Fri Sep 06 02:34:37 EDT 2013 | rollon65

Hi Marcelo The two machines I mentioned are the American type but they have an internal transformer fitted to convert from 110 to 220 Volts for U.K. Incidentally only one of the machines does it on a regular basis whilst the other one is mostly O.K

Quad 4C power switch

Electronics Forum | Wed Aug 07 16:56:32 EDT 2013 | marcelorotofrance

When I turn the machine on, almost every time I turn the Motor Power Switch it trips. I must to put the lever down and raise it again, then every runs normally. I asked to the former owner about that and told me that this machine always did it so and

Quad 4C power switch

Electronics Forum | Mon Aug 19 15:21:17 EDT 2013 | marcelorotofrance

Hi Rollon, thanks for your answer. At this point it seems that cold-start current surge, because the presence of large value capacitors in the power source, exceeds the sensitivity of the protection switches rather than a malfunction. Nevertheless, i

Quad 4c not placing components

Electronics Forum | Thu Sep 05 07:14:16 EDT 2019 | smrsteve

Hello Bobpan, Thanks for the suggestions. Sorry I didn't reply yesterday as I'd gone home - I'm in the UK, so I'm guessing there's a time difference. Okay, I found the control to turn off the vacuum verify - it's SHIFT - SWITCH/VERIFY. Makes no di

QUAD 4C motor error #5

Electronics Forum | Fri Aug 30 05:34:28 EDT 2013 | bobpan

I would check the following: 1. Make sure the head can move in all axis including z and theta by physically moving each. 2. Check the voltage from the main power supply which is located in the middle of the machine on the top of the main board asse

experience with Quad 4C retrofit from ppm?

Electronics Forum | Fri Jul 10 19:00:01 EDT 2020 | tristanlund

Its nice to have Qsoft on a 4c, its a lot more user friendly than the old system. but.. 1.It doesn't increase the machines accuracy 2.All of PPM's software is very buggy, We ended up switching all our Q machines back to Quad's windows 98 software fo

  1 2 3 Next

quad 4c dip switch searches for Companies, Equipment, Machines, Suppliers & Information

Shenzhen Honreal for all your SMT Equipment needs

Component Placement 101 Training Course
Blackfox IPC Training & Certification

Wave Soldering 101 Training Course
pressure curing ovens

World's Best Reflow Oven Customizable for Unique Applications