Electronics Forum: quad 4c skip repeat (Page 1 of 2)

Quad 4c programming question

Electronics Forum | Fri Mar 04 19:38:44 EST 2011 | olddog

We are a very small (2 people) company and have recently purchased a used Quad 4c Mk II, for our low-volume in-house production. The machine appears to work perfectly for our needs. My question is regarding programming from a concept standpoint. Our

Quad 4c programming question

Electronics Forum | Mon Mar 07 06:51:31 EST 2011 | mosborne1

Tim you can do your image repeat after you place the whole panel with nozzle #1. In your sequence step program place all with nozzle 1. You can then change to nozzle#2 then place the whole panel with nozzle number 2. This will be one nozzle change. I

Quad 4c LAE

Electronics Forum | Wed Apr 11 00:40:19 EDT 2012 | ngineer

I have a problem setting up the LAE on my Quad 4c. I set it up for 0805, and it seems to work, although it rejects a lot of parts, at least it places "most" of them. I tried setting up on a soic14, and could not get even one to pass. I believe I h

Quad 4C reject PCB stickers

Electronics Forum | Mon Jun 17 06:56:50 EDT 2013 | bobpan

Did you teach the reject mark? Sounds like a lighting issue when looking for the white sticker. You can also skip images by pressing control-repeat after the machine has found fiducials. Good luck

Quad 4C reject PCB stickers

Electronics Forum | Wed Jun 19 07:24:10 EDT 2013 | bobpan

Hello Rollon, There needs to be a contrast between the sticker and board. The manual gives and example of a round red sticker. If you still cant still make this work.....Do the following. Run the machine and after it finds fiducials press stop on the

0402 placement using Quad 4C

Electronics Forum | Tue Mar 13 13:10:09 EST 2001 | onset

As long as you perform a repeat pickup on the part with an ordinary feeder you will be fine.

0402 placement using Quad 4C

Electronics Forum | Thu Mar 15 17:34:38 EST 2001 | rentreo

I place 0302's on my Quad 4c's all the time. Use a repeat pick-up just like a waffle tray part but make sure the z height is perfect on your pick-up or you will bounce the other parts out of their pockets. Also change your mod code to only try once o

0402 placement using Quad 4C

Electronics Forum | Tue Mar 13 12:15:14 EST 2001 | onset

We have a 4C and it places 0402 components without any problems. The tricky part is getting the machine to pick them up out of the feeder it takes patience but you will get it. jake p.s. you

Quad IV C Recommendations

Electronics Forum | Tue Jan 11 13:28:14 EST 2011 | jmw

0603 and up should be no problem on the machine. If you are doing under 25 mil pitch the machine needs an upward camera to repeatably place the parts. You will always lose the first 10 or so parts with cut tape but that should be about it. Repair par

Quad 4C part placement rejection

Electronics Forum | Wed Nov 16 05:12:36 EST 2011 | bobpan

A couple of things i would try: 1. Does function 30 give you a nozzle height that is repeatable. The number should be around 200.....+/- 20 or so. 2. I would change the z-rod because the spring could be worn out and when the vacuum turns on....it ca

  1 2 Next

quad 4c skip repeat searches for Companies, Equipment, Machines, Suppliers & Information

2024 Eptac IPC Certification Training Schedule

Software for SMT placement & AOI - Free Download.
Win Source Online Electronic parts

Smt Feeder repair service centers in Europe, North, South America
SMTAI 2024 - SMTA International

Stencil Printing 101 Training Course
PCB Handling Machine with CE

Wave Soldering 101 Training Course
Electronic Solutions R3

Private label coffee for your company - your logo & message on each bag!