Electronics Forum: quad 4c startup (Page 1 of 33)

quad 4c

Electronics Forum | Fri Nov 15 12:36:56 EST 2002 | bobbyv40

We are currently considering purchasing a Quad 4c. Any recomendations or discouragements for this machine? All comments will be greatly appreciated.

quad 4c

Electronics Forum | Fri Nov 15 14:06:08 EST 2002 | Claude_Couture

From personal experience with 4c's: run away as fast and as far away from them as you can. These will bring you nothing but grief.

quad 4c

Electronics Forum | Wed Nov 27 15:42:50 EST 2002 | al

I am with Claude on the Quad....run fast and far. Why not go with a GSM instead, There are many who support these. The Earlier GSM 1's are as cheap as ever now too. Al

quad 4c

Electronics Forum | Mon Nov 18 12:07:02 EST 2002 | smckee

It would have to be really CHEAP! I ran one a few years ago, had 3 4C's gained together. Always had problem with the software and it was a high maintenance machine. Never had such problems with Mydata, Phillips or Zevatech. Also, it seemed I alwa

quad 4c

Electronics Forum | Mon Nov 25 16:10:27 EST 2002 | btaylor

I have run the 4Cs for over 8 years it has been a good little machine. We use it for placing 10 mil pitch flip chips. I buy the yearly insurance through Tyco every year.

quad 4c

Electronics Forum | Fri Nov 29 08:36:07 EST 2002 | Jeff Park

They have there strong points and weak ones. I have worked with them for the last 5 years and have seen some flakey problems (Cables, feeders, encoders) that will cause you some down time but if you get a good price on a system it might be worth it.

quad 4c

Electronics Forum | Wed Nov 27 18:10:41 EST 2002 | andrewbrook

Quad4C's have their moments. If the price is right and you are aware of the machines limitations then you will be satisfied. The placement rate is slow, 1.2 seconds/chip. Don't buy any Quad if it has the CyberOptics Laser unit, the Quadalign unit is

quad 4c

Electronics Forum | Mon Nov 18 11:14:57 EST 2002 | bpan

Very good machine. Dont know about Claude but sounds like he doesnt know the machine too well. Be careful if you buy it because Tyco's Parts support for the machine are terrible. For ex. Tried to buy a sensor for the lifters on our transport and they

quad 4c

Electronics Forum | Thu Nov 21 11:35:47 EST 2002 | hannahsd

We had several 4c's before we put them out to pasture. From my experience they are easy to make program adjustments, but like the previous person responded the auto programmer did not work for us. We had laser coplanarity check as an addition to th

quad 4c

Electronics Forum | Wed Nov 27 09:51:08 EST 2002 | Claude_Couture

I have worked with 4c's for two years. The feeders are "tinker toys" with a mechanism that slips, so the pick-up has to be adjusted several times as the reel is used, especially with 13" reels. The worm gear was plastic on the steel shaft of the moto

  1 2 3 4 5 6 7 8 9 10 Next

quad 4c startup searches for Companies, Equipment, Machines, Suppliers & Information

Win Source Online Electronic parts

Software programs for SMT placement and AOI Inspection machines from CAD or Gerber.
Sell Used SMT & Test Equipment

High Throughput Reflow Oven
December 2024 Auction

World's Best Reflow Oven Customizable for Unique Applications
Software for SMT

Nozzles, Feeders, Spare Parts - Siemens, Fuji, Juki, Yamaha, etc...
PCB separator

Internet marketing services for manufacturing companies