Electronics Forum: quad aligner (Page 1 of 19)

quad 4c

Electronics Forum | Fri Nov 29 08:36:07 EST 2002 | Jeff Park

They have there strong points and weak ones. I have worked with them for the last 5 years and have seen some flakey problems (Cables, feeders, encoders) that will cause you some down time but if you get a good price on a system it might be worth it.

quad qsp-2

Electronics Forum | Mon Nov 29 18:23:19 EST 2010 | comprep

Has anyone had any success with placing BGAs with the Quad QSP-2? We have been having alignment issues with BGA placement but our placement of 0402 parts is dead on. We have worked through the calibration and it seems to be correct.

quad 4c

Electronics Forum | Wed Nov 27 18:10:41 EST 2002 | andrewbrook

Quad4C's have their moments. If the price is right and you are aware of the machines limitations then you will be satisfied. The placement rate is slow, 1.2 seconds/chip. Don't buy any Quad if it has the CyberOptics Laser unit, the Quadalign unit is

quad qsv-1 gantry - quad align issues

Electronics Forum | Wed Jan 23 14:30:09 EST 2008 | operator

Additionally, I have seen the bad align error from incorrect pickup Z. Quad align can freak out sometimes if it sees something it doesn't like. If all else fails I just reboot and 99% of the time the problem goes away.

quad align init problem

Electronics Forum | Fri Apr 23 10:53:24 EDT 2010 | evertonsanches

Hello Sir, in this situation I recommend you to check and reconect the conectors of Quad Align Board and also of Quad Align Sensor. Everton - Brasil

quad qsv-1 gantry - quad align issues

Electronics Forum | Wed Jan 23 11:28:47 EST 2008 | tbkonrad

Help! Since last Friday i have been having issues with a Quad qsv-1, it all started with a quad align error, i found there to be a small quantity of grease covering the lenses on both quad align sensors. I wiped the grease off and then everything s

quad qsv-1 gantry - quad align issues

Electronics Forum | Wed Jan 23 14:26:52 EST 2008 | operator

I have seen the bad alignment error many times and never had to replace the head for it. It usually has something to do with the laser windows being dirty or cracked. Also it could be your profile settings. Make sure all of these things are perfect b

quad align init problem

Electronics Forum | Thu May 20 10:01:23 EDT 2010 | jmw

Just a slight correction....the quad align card is located at the back rear right of the machine (in a cage). If it is a cyber-optics 4c machine....the laser align card is in the front card rack to the far left.

quad qsv-1 gantry - quad align issues

Electronics Forum | Wed Jan 23 13:02:35 EST 2008 | tbkonrad

Thanks for the info. I called Mike Tieman earlier and he recommended I do the exact same things. He said that there should be very little resistance on the theta of the Z-rods, (not the case) so he recommended that the P4 head be replaced. Mike is

quad align init problem

Electronics Forum | Fri Apr 23 09:13:04 EDT 2010 | kdaglio

for the last couple of days when i power up our quad iv, i get assembler is off errors. i cannot get the machine and the quad align to start. any help is gratly appreciated.

  1 2 3 4 5 6 7 8 9 10 Next

quad aligner searches for Companies, Equipment, Machines, Suppliers & Information

best reflow oven

IPC Certification Training from the comfort of your home or office
Non-heated dispensing system

Training online, at your facility, or at one of our worldwide training centers"
2023 Eptac IPC Certification Training Schedule

MSD Dry Cabinets
PCB Handling Machine with CE

High Speed Precision In-Line SPI System - Mirtec MS-11
BGA and SMD Rework Stations

SMT & PCB Equipment - MPM, DEK, Heller, Europlacer and more...