Electronics Forum: quad feeder z (Page 1 of 48)

Axis head 2 z velocity error

Electronics Forum | Sat Jan 13 19:34:16 EST 2007 | geb

(Its a flex head) I have made a trial program to determine at what point it stops. This is how it goes: I load the program, push the start button it will zero and pick components with head 1. As soon as it finishes placing head 1 parts it halts wher

quad 4c

Electronics Forum | Wed Nov 27 18:10:41 EST 2002 | andrewbrook

Quad4C's have their moments. If the price is right and you are aware of the machines limitations then you will be satisfied. The placement rate is slow, 1.2 seconds/chip. Don't buy any Quad if it has the CyberOptics Laser unit, the Quadalign unit is

quad 4c

Electronics Forum | Wed Nov 27 09:51:08 EST 2002 | Claude_Couture

I have worked with 4c's for two years. The feeders are "tinker toys" with a mechanism that slips, so the pick-up has to be adjusted several times as the reel is used, especially with 13" reels. The worm gear was plastic on the steel shaft of the moto

quad 4c

Electronics Forum | Fri Nov 29 08:36:07 EST 2002 | Jeff Park

They have there strong points and weak ones. I have worked with them for the last 5 years and have seen some flakey problems (Cables, feeders, encoders) that will cause you some down time but if you get a good price on a system it might be worth it.

quad 4c

Electronics Forum | Mon Nov 18 12:07:02 EST 2002 | smckee

It would have to be really CHEAP! I ran one a few years ago, had 3 4C's gained together. Always had problem with the software and it was a high maintenance machine. Never had such problems with Mydata, Phillips or Zevatech. Also, it seemed I alwa

Has anyone heard of z scan bar code feeder system?

Electronics Forum | Thu Jul 27 17:42:15 EDT 2000 | JD of Panasonic Create

Have you heard of them and where can I get information on their systems? Sincerely, J.D. jtalken@panasonicfa.com

quad qsv-1 gantry - quad align issues

Electronics Forum | Wed Jan 23 15:13:54 EST 2008 | tbkonrad

It's not the z pickup or profile bot thanks for the help, I think Mike is right. I have used these profiles hundreds if not thousands of times in the past and never had an issue. Also it was different components and different profiles almost every ti

quad qsv-1 gantry - quad align issues

Electronics Forum | Wed Jan 23 14:30:09 EST 2008 | operator

Additionally, I have seen the bad align error from incorrect pickup Z. Quad align can freak out sometimes if it sees something it doesn't like. If all else fails I just reboot and 99% of the time the problem goes away.

quad qsv-1 gantry - quad align issues

Electronics Forum | Wed Jan 23 13:02:35 EST 2008 | tbkonrad

Thanks for the info. I called Mike Tieman earlier and he recommended I do the exact same things. He said that there should be very little resistance on the theta of the Z-rods, (not the case) so he recommended that the P4 head be replaced. Mike is

quad qsv-1 gantry - quad align issues

Electronics Forum | Wed Jan 23 12:35:24 EST 2008 | bobpan

Here is a few things to try.... 1. Spin the z-shaft with your fingers and make sure it is smooth and easy to turn. 2. Check your handling in your profile for the part that the software is locking up on.......You cannot go any slower than 40% or this

  1 2 3 4 5 6 7 8 9 10 Next

quad feeder z searches for Companies, Equipment, Machines, Suppliers & Information