Electronics Forum: quad qsv-1 sensor (Page 1 of 10)

quad qsv-1 gantry - quad align issues

Electronics Forum | Wed Jan 23 11:28:47 EST 2008 | tbkonrad

Help! Since last Friday i have been having issues with a Quad qsv-1, it all started with a quad align error, i found there to be a small quantity of grease covering the lenses on both quad align sensors. I wiped the grease off and then everything s

quad 4c

Electronics Forum | Mon Nov 18 11:14:57 EST 2002 | bpan

Very good machine. Dont know about Claude but sounds like he doesnt know the machine too well. Be careful if you buy it because Tyco's Parts support for the machine are terrible. For ex. Tried to buy a sensor for the lifters on our transport and they

quad qsv-1 gantry - quad align issues

Electronics Forum | Wed Jan 23 14:30:09 EST 2008 | operator

Additionally, I have seen the bad align error from incorrect pickup Z. Quad align can freak out sometimes if it sees something it doesn't like. If all else fails I just reboot and 99% of the time the problem goes away.

quad qsv-1 gantry - quad align issues

Electronics Forum | Wed Jan 23 13:02:35 EST 2008 | tbkonrad

Thanks for the info. I called Mike Tieman earlier and he recommended I do the exact same things. He said that there should be very little resistance on the theta of the Z-rods, (not the case) so he recommended that the P4 head be replaced. Mike is

quad qsv-1 gantry - quad align issues

Electronics Forum | Wed Jan 23 14:26:52 EST 2008 | operator

I have seen the bad alignment error many times and never had to replace the head for it. It usually has something to do with the laser windows being dirty or cracked. Also it could be your profile settings. Make sure all of these things are perfect b

quad qsv-1 gantry - quad align issues

Electronics Forum | Wed Jan 23 12:35:24 EST 2008 | bobpan

Here is a few things to try.... 1. Spin the z-shaft with your fingers and make sure it is smooth and easy to turn. 2. Check your handling in your profile for the part that the software is locking up on.......You cannot go any slower than 40% or this

quad qsv-1 gantry - quad align issues

Electronics Forum | Wed Jan 23 15:13:54 EST 2008 | tbkonrad

It's not the z pickup or profile bot thanks for the help, I think Mike is right. I have used these profiles hundreds if not thousands of times in the past and never had an issue. Also it was different components and different profiles almost every ti

quad 9QSV-1 Plus)

Electronics Forum | Fri Feb 03 14:32:59 EST 2006 | mazink

Hello BOb, Sorry, I wasn't getting your responed because i wasn't log in completlt. I sent an email yesterday which is as follow.. I have a quad machine (QSV 1 PLUS) here and I been having problem with it since 2 month. massege keep coming says 1) B

quad 1000 error

Electronics Forum | Fri Feb 03 12:53:19 EST 2006 | MazinK

Hello BobPan, I sent you a message yesterday ! I was wondering !did you get it regarding QSV 1 Plus. Please Advise!

quad 1000 error

Electronics Forum | Mon Feb 06 13:16:49 EST 2006 | mazink

Hello BOb, Sorry, I wasn't getting your responed because i wasn't log in completlt. I sent an email yesterday which is as follow.. I have a quad machine (QSV 1 PLUS) here and I been having problem with it since 2 month. massege keep coming says 1) B

  1 2 3 4 5 6 7 8 9 10 Next

quad qsv-1 sensor searches for Companies, Equipment, Machines, Suppliers & Information

ISVI - Industrial Sensor Vision International Corporation
ISVI - Industrial Sensor Vision International Corporation

Industrial Sensor Vision International specializes in advanced camera technology of high resolution fast speed cameras for automation, AOI, 2-D/3-D, SPI inspection and wafer inspection.

Manufacturer

3 Morse Road 2A
Oxford, CT United Arab Emirates

Phone: +1 203 592 8723