Electronics Forum: raising table error (Page 1 of 18)

How do I adjust table height EKRA X5 Screen Printer?

Electronics Forum | Tue Aug 04 13:45:03 EDT 2020 | oxygensmd

There are one value for thickness during PCB-teach function which is the PCB thickness. The other one is the camera focus in machine option but it is a dangerous function because the camera focus is adjusted by raising/lowering table.

How do I adjust table height EKRA X5 Screen Printer?

Electronics Forum | Wed Aug 05 06:34:33 EDT 2020 | oxygensmd

Yes if you adjust the thickness to be thin than the machine raise the PCB more to the stencil - than the foil have better tension but it string out faster.

F4G CP4 Optimizer: Cycle time table file not found?

Electronics Forum | Thu Dec 09 13:22:24 EST 2010 | rodrigo

Hi All, I'm trying to use the F4G CP-4 optimizer. I cleared all the issues I was having except for this error I get at the end: Execute, 2030: Cycle Time table file not found I see a file in one of the folders named CP4_CYC.TBL but I'm not sure if

Quad QSV-1 error msg

Electronics Forum | Wed May 09 08:48:51 EDT 2012 | leemeyer

Try going into the program definition screen and delete the permanent table top. Then shut down and reboot. The permanent table top will be re created upon reboot.

Topaz X error

Electronics Forum | Tue Feb 12 12:47:02 EST 2019 | slthomas

Someone with some more definitive knowledge of these machines will no doubt chime in at some point, but my thought was that the "A-table" is just a data table that stores I/O information. Thus, being "off in A-table YV100X:N2323 YV100XT:n2223" just m

Topaz X error

Electronics Forum | Fri May 10 01:42:13 EDT 2019 | vinitverma

A Table is something that you can ignore right now. It is significant only in case of dual table machines such as Sapphire or Sapphire-X which have A and B tables (two independent PCBs being handled at the same time). In case of Topaz or Topaz X or E

Quad QSV-1 error msg

Electronics Forum | Tue May 08 15:00:26 EDT 2012 | jorge_quijano

Hello guys, I have a error message in a QSV-1 machine, when it tuns on "File archive error occurred while reading header of table top:permanent table top", I have no experience with this machine, so no good so far, already escalated to service and wa

Topaz X error

Electronics Forum | Tue Feb 12 11:26:31 EST 2019 | aldrich17

Does anyone have any info. on an "E869" error code on a Phillips Topaz X SMT machine. Error screen shows "Nozzle down limit sensor is off in A-table YV100X:N2323 YV100XT:n2223 Please check sensor and remove to the cause of this sensor being off.

S25 Software booting error

Electronics Forum | Mon Nov 29 13:39:48 EST 2021 | oxygensmd

Is it a running machine or a first startup? For me, it seems to be some configuration error. For example problem with some card (iCos, MC, servo controller). At first check table and WPC connectors are fitted properly than check the status LEDs on y

Quad IV-c feeder error

Electronics Forum | Sun Feb 03 07:36:17 EST 2019 | dfl

Hey Steve, I wrote to Bob, but he doesn't reply yet. Digging around, I found these: HANDLING COMPONENT VARIETY The adjustable Pocket Index function enables handling a variety of component tape reels or special component packaging. The following ins

  1 2 3 4 5 6 7 8 9 10 Next

raising table error searches for Companies, Equipment, Machines, Suppliers & Information