Electronics Forum | Mon Apr 19 22:52:59 EDT 1999 | Dean
25 PPM)! | | 1. Is there a better process to solder the leads of QFP's with lifted "minute" lifted leads still having a realiable solder joints? | | 2. Or has anybody tried modifying solder pads and use thicker solder paste deposit to compensate fo
Electronics Forum | Tue Apr 20 23:18:48 EDT 1999 | KEVIN SIMPSON
25 PPM)! | | 1. Is there a better process to solder the leads of QFP's with lifted "minute" lifted leads still having a realiable solder joints? | | 2. Or has anybody tried modifying solder pads and use thicker solder paste deposit to compensate fo
Electronics Forum | Fri Apr 16 11:23:26 EDT 1999 | Scott McKee
| | Any recommendations for a reballer for BGA and mBGA? Low volume, low cost appreciated! | | | Dave: I don't believe that reballing BGAs that go into customer products is a good idea. Check with your BGA supplier to determine their recommended
Electronics Forum | Tue Apr 06 16:22:58 EDT 1999 | Dave F
| 0603's and 0402's are being damaged by the water wash post reflow. PCA's are 1" X 4" and 2" X 2" approximately. | | We've adjusted water pressure so that the top-down is higher than the bottom up. | | The baskets have a .5" mesh spacing. Some
Electronics Forum | Wed Mar 24 19:26:25 EST 1999 | Marc Ruggiero
| Hi Folks, | This is my first surface mount board, so I asked our assembly house for some tips. They said only passives on the bottom side-preferably no smaller than 0805, 0603 only if I have to. I would think that an SOT-23 would be OK on the botto
Electronics Forum | Mon Mar 15 09:55:53 EST 1999 | Justin Medernach
| After rmoving a BGA (plastic)to correct unexplained shorts | I installed another BGA using flux only. | Checking on an X Ray machine and found two shorts. | | can anyone give a good explenation ? | | Thanks | | Ron | Ron, It could be a number o
Electronics Forum | Thu Mar 04 17:10:19 EST 1999 | Earl Moon
| Our vendor proposed to supply us with shields made out of Cold Rolled Steel (CRS) electroplated with Sn (50 - 150 minches). Should I be concerned with solderability or are there a better alternatives to tin finish? | No matter the base metal, elec
Electronics Forum | Mon Mar 01 11:03:51 EST 1999 | Dennis Xiong
Hello! SMT professionals, I do not know if anyone posted this question before. Last week, I reflowed our newly designed thin Rigid-Flex pcb with 0.040" thickness. I found all of pins of a TQFP48 ic did not get wetted. I could see on the heel side o
Electronics Forum | Mon Mar 01 11:03:22 EST 1999 | Dennis Xiong
Hello! SMT professionals, I do not know if anyone posted this question before. Last week, I reflowed our newly designed thin Rigid-Flex pcb with 0.040" thickness. I found all of pins of a TQFP48 ic did not get wetted. I could see on the heel side o
Electronics Forum | Mon Mar 01 09:49:04 EST 1999 | Justin Medernach
| It seems to be that we have to much NaCl left on our assambled PCB's. | The flux we use is from cobar. They say it can not be from the flux... So what can be the reason, what kind of problem may occer when there is to much NaCl. | George, Are you
Reflow ovens for automated SMT PCB assembly, specializing in lead free processing and nitrogen reflow. The best convection reflow ovens on the market.
4 Vreeland Rd.
Florham Park, NJ USA
Phone: 973-377-6800