Electronics Forum: removing and glue and from and pcb's (Page 1 of 2)

help to id and purchase pcb transformer from LOWRANCE GPS

Electronics Forum | Sat Jun 25 15:20:03 EDT 2016 | skipper6567

I have a mini/micro transformer that is mounted on a pcb inside my lowrance gps/plotter. I have removed it from the pcb. It has 5 through hole pins, 3 pins out bottom one side and 2 pins out bottom on opposite side. The transformer has yellow tape ar

Wave flux and profiling

Electronics Forum | Wed Dec 20 04:43:36 EST 2006 | greg york

Any decent flux would volatise off with the heat of the wave unless absorbed into the solder mask. Test this by trying to clean in alcohol or common solvent aerosol, if it does not clean then it is probably Mineral Salts from solder mask fillers. Ano

LGA and Solderballs

Electronics Forum | Tue Nov 28 21:16:17 EST 2006 | davef

J Rose at EMPF says: The introduction of no-clean solder fluxes in electronics manufacturing has given rise to greater levels of solder balling simply because the opportunity to remove them in the wash process does not exist. They are typically cause

Wave and Reflow Profiler

Electronics Forum | Tue Feb 19 09:41:26 EST 2008 | slthomas

ECD sells the MOLE, and they sell both the Oven Rider and the Wave Rider to accompany it. The thing is, you can profile both an oven and a wave machine without either if you're willing to just solder your thermocouples to a board. The nice thing ab

Re: Voids and BGA

Electronics Forum | Sun Mar 01 15:52:13 EST 1998 | Earl Moon

| From several months I am investigation about the VOIDS PERSENCE and his important as reliability. | One question now is : | It is possible that on the BGA components the voids are already present into the balls, before the mounting on the pcb ? | I

Cleaning Machine and Chemistry

Electronics Forum | Mon Feb 19 11:36:39 EST 2001 | billschreiber

Hello Mark, I wish it were that simple so I could direct you to a particular manufacturer and stencil cleaner model. Unfortunately, there are several issues complicating the process of cleaning all these applications in one machine. First and fore

Re: Geometric Dimensioning and Tolerancing

Electronics Forum | Sun Jun 07 02:06:26 EDT 1998 | Earl Moon

| Earl, | As always, I am interested in what you have to say, but I am still a little vague on your application of ANSI Y14.5 as it relates to the manufacturability of an assembled printed circuit board. Are you implying that component placement coor

Coils and Water Soluble Fluxes

Electronics Forum | Wed Oct 10 13:51:08 EDT 2007 | petep

Coilcraft has posted the following and I am wondering how you folks are handling the use of coils in a Water Soluble world. PCB Washing and Coilcraft Parts Coilcraft tests for resistance to solvents per the following specification: Resistance to s

Clearance between Through hole and chip component

Electronics Forum | Tue Feb 27 11:03:09 EST 2007 | Marcin

Hi All, Anybody knows what is the minimum clearance between through hole component and chip component? Problem description: On bottom side of my pcb are only 0603 chip components mounted on glue. One of the component is located very close to hole

Yestech B3 Capacitors and P+P downtime

Electronics Forum | Tue Apr 05 10:36:24 EDT 2011 | frcdave

Hi Don, The YESTech B3 can be used post placement very easily. I would suggest contacting their service team, they could walk you through the process quickly. You are actually very close to being able use it now in that capacity since you have the i

  1 2 Next

removing and glue and from and pcb's searches for Companies, Equipment, Machines, Suppliers & Information

thru hole soldering and selective soldering needs

World's Best Reflow Oven Customizable for Unique Applications
Blackfox IPC Training & Certification

Benchtop Fluid Dispenser
Pillarhouse USA for Selective Soldering Needs

Wave Soldering 101 Training Course
PCB Depanelizers

Find a wide selection of nozzles, solder materials, storage solutions and more at SALESCON