Electronics Forum: selective solder nozzles (Page 1 of 177)

customized selective solder

Electronics Forum | Fri Apr 28 10:50:26 EDT 2017 | emeto

Hello experts, Here is my problem: I have a board that has smt parts on one side and TH parts on the other. We designed special pallet for wave, but the pallet itself is 15mm thick, so we are still seeing some defects. Have any of you tried to find

selective solder process attributes

Electronics Forum | Mon Nov 10 08:53:23 EST 2014 | jpal

We have the opportunity to buy a new selective solder machine and are used to using a very old Jade machine with a moving tank and wetted nozzle. I have two process concept questions: Which is better- move the board over the nozzle or move the nozz

selective solder process attributes

Electronics Forum | Thu Nov 13 12:49:45 EST 2014 | dyoungquist

I have no experience running a "move the board" selective solder so can not compare the 2 methods..... We have been using an RPS Rhythm "move the pot/nozzle" system since 2008. We are using it solder thru hole components onto boards that often have

Kiss selective solder flux

Electronics Forum | Fri Mar 22 14:19:38 EDT 2019 | gregcr

Thank you ProcEng1 Nordson sent me a flux suggestion list: No Clean: 1. Kester Select 10 2. ALPHA EF-2210 3. AIM FX-16 Water Sol: KESTER 2331-ZX Nozzle Tinning: SUPERIOR #75

selective solder process attributes

Electronics Forum | Mon Nov 10 09:03:47 EST 2014 | rgduval

I can't claim to be an expert....I've just bought a used RPS, and it'll be my first...but, after reading through their manual, and working on setting things up, I'd say: -Conceptually, I like the idea of moving the board rather than moving the entir

selective solder process attributes

Electronics Forum | Fri Nov 14 10:40:35 EST 2014 | eniac

I use a two machines from EBSO, Germany. It's a machines with PCB carrier, so, solder pot is fixed. I'm fully satisfied with this equipment, but I use only wettable nozzles. If you would like to buy a new machine, not in used condition, EBSO will be

Lead free selective solder

Electronics Forum | Fri Jun 23 12:54:53 EDT 2017 | guts1872

We are having issues with top fill and dropping pins on Molex connectors with our KISS 101. Unfortunately we do not have a pre heater and bottom side pre heat with our nozzles is not satisfactory. Most of the issues occur when using a no clean proces

selective solder process attributes

Electronics Forum | Fri Nov 14 10:45:22 EST 2014 | tombstonesmt

We use both types in house. We started with a board moving over the pot, slowly moved on to Jade machines and eventually Synchrodex. Like you mentioned without palletizing you'll have component movements during the cylce and most likely won't have th

Problems getting selective nozzles off

Electronics Forum | Thu Jan 03 10:32:38 EST 2013 | beej

I was wondering if any of you fine folks had a trick to changing out nozzles for a Pillerhouse Jade Handex. The tool they gave us when we purchased the machine is inadequate at best. I have tried heating the nozzle up, to no avail. Just wondering if

Problems getting selective nozzles off

Electronics Forum | Thu Jan 03 14:19:33 EST 2013 | uksolder

Beej, The tool supplied works well as long as the bath is up to temp and the nozzle tip was not cross threaded when fitted. Did you apply a small amount of the anti seize paste before the nozzle tip was fitted? I have seen dry tight threads if not ap

  1 2 3 4 5 6 7 8 9 10 Next

selective solder nozzles searches for Companies, Equipment, Machines, Suppliers & Information

High Precision SMT Fluid Dispensers

Best Reflow Oven
Electronics Decoating Agent

Repair tools for all your electronic circuit board repair needs.
SMT feeders

Software programs for SMT placement and AOI Inspection machines from CAD or Gerber.