Electronics Forum: set up time (Page 1 of 525)

DEK Printer Chiller set up

Electronics Forum | Mon May 02 10:13:42 EDT 2016 | swag

If it's like ours, it's an AC unit, not a chiller. Easy to hook up with a hose to the printer + power to the unit. You'll need to empty the water from the drip pan from time to time (collects condensation).

Re: Flux sprayer set up

Electronics Forum | Tue Dec 21 13:27:47 EST 1999 | Vince Whipple

Charlie: As far as setting up a spray fluxer.. Are you spraying no-clean, voc free, water soluble? What you would want to do is to run a blank pcb through the fluxer and pop it out before the preheaters. Visually inspect for variations in uniformit

How to set warm-up time of solder paste

Electronics Forum | Tue Feb 28 03:33:29 EST 2006 | snowcaj

To set warm-up time,which standard should we select and how should we measure? Thanks!

How to set warm-up time of solder paste

Electronics Forum | Tue Feb 28 13:46:28 EST 2006 | slthomas

Assuming you're using DOM and shelf life to determine what's good and what's not, you just have to know 1)the rate at which you use it up, 2) how much shelf life is left, and 3) the rate that it goes bad when not refrigerated. From that you can tel

Flux sprayer set up

Electronics Forum | Mon Dec 20 12:42:15 EST 1999 | Charlie

There is a need to set up the spray fluxer on our wave machine. I'm looking for guidelines and comments form others who have done this set up. Also, is there any rule of thumb at visual inspection when there is too much or not enough flux being appli

Quadalign set up

Electronics Forum | Fri Sep 25 10:28:08 EDT 2009 | leemeyer

Are you running Q-soft software or is this an older machine running central controller ? Do you have seperate profiles set up for 0603 caps and 0603 resistors or just one profile for all 0603 parts. It sounds to me that you might be scanning to low a

Quadalign set up

Electronics Forum | Mon Sep 28 06:03:28 EDT 2009 | bobpan

You are probably scanning below the part. Adjust the scan height closer to 0 ex..(.005) and see if that works. If not....its probably the z-rod and the nozzle not seating on it correctly. Good luck

Quadalign set up

Electronics Forum | Thu Sep 24 17:00:03 EDT 2009 | dogsbody

would any body be able to supply me with infomation on how to adjust a quadalign unit,as a unit on my line will not pick up 0603 resistors,but will pick up thicker 0603 caps. My manuals offer no help.I have run the aligner calibration with the cone t

Quadalign set up

Electronics Forum | Fri Sep 25 14:58:33 EDT 2009 | gantry228

It is apparently a Q-series machine, if the adjustment for pitch and roll doesn't work. You may have to loosen or remove the quadalign then check the "wavey" washers to ensure they are there and opposing each other (these provide like a spring effect

Re: Flux sprayer set up

Electronics Forum | Mon Dec 20 17:02:39 EST 1999 | Dave F

Charlie: There's a lot of background setting-up fluxers (including sprayers) in the archives. Chris Shea wrote a paper that's in the library (or where ever SMTnet stores stuff like that) that is pretty good. Good luck. Dave F

  1 2 3 4 5 6 7 8 9 10 Next

set up time searches for Companies, Equipment, Machines, Suppliers & Information

Best SMT Reflow Oven

High Resolution Fast Speed Industrial Cameras.
One stop service for all SMT and PCB needs

IPC Certification Training from the comfort of your home or office
PCB Handling Machine with CE

We offer SMT Nozzles, feeders and spare parts globally. Find out more
Selective soldering solutions with Jade soldering machine

High Throughput Reflow Oven
convection smt reflow ovens

World's Best Reflow Oven Customizable for Unique Applications