Electronics Forum: setup (Page 87 of 149)

SMT Barcode controls

Electronics Forum | Thu Aug 20 15:12:44 EDT 2015 | superlen

I don't know that you find anything off the shelf that fits all of your requirements, but it wouldn't be too hard to create a system that does *most* of what you want. You could at least have it read the code off the pcb & alarm if it doesn't match

gas to extend allowed print-to-place time?

Electronics Forum | Mon May 02 12:28:03 EDT 2016 | adamjs

Why can't you place the entire job the same day you paste it? I can. But setting up and properly cleaning the stenciling machine takes 2-3 hours. We only run one shift. If we do that every day we're spending most the time on setup+teardown. Much

Pick and Place vs CAD File

Electronics Forum | Fri Oct 06 06:59:00 EDT 2017 | spoiltforchoice

I agree, in Essemtec's case all they needed to to make that 100% friendlier was let the layout visualiser be able to read and display some gerber data (paste and overlay). Otherwise the offline solution is to hold up a blank board/printout to verify

Re: pre-heat settings for wave solder - an answer to Gary's ? - Hi C.K. (Mini K)!

Electronics Forum | Fri Jun 23 12:30:24 EDT 2000 | Super K (Evil K)

To answer Gary's question: Gary, you will need a production board, thermal profiler, flux vendors product data sheet on the flux you intend to use, maybe your wave vendor service engineer or wave solder vendor contact (unless you know your wave) and

Re: pre-heat settings for wave solder - an answer to Gary's ? - Hi C.K. (Mini K)!

Electronics Forum | Fri Jun 23 12:32:20 EDT 2000 | Super K (Evil K)

To answer Gary's question: Gary, you will need a production board, thermal profiler, flux vendors product data sheet on the flux you intend to use, maybe your wave vendor service engineer or wave solder vendor contact (unless you know your wave) and

Re: Wave Solder balls

Electronics Forum | Tue Nov 03 16:28:21 EST 1998 | Dave F

Well my process is I'm running my belt speed at 3.50fpm and about 215 to 225 degrees top side. I got my main wave down to a little less than half the board thickness. I'm not using a hot air knife cause we thought it might create more of a problem

Re: Solder mask materials and equitements wanted

Electronics Forum | Sat Aug 29 08:43:35 EDT 1998 | Dave F

Hi, Friends, Could you please recommend me some solder mask materials and equitements for high quality solder mask? Details such as company name, phone numer et al are welcomed. Thanks! Have a good day Xingsheng Xingsheng: Consider the follo

Re: Placement machine component management

Electronics Forum | Thu Apr 02 11:41:26 EST 1998 | Scott Cook

Hello, We are currently trying to design and ultimately implement a system that will be able to count and manage component placement for three Sanyo chipshooters on three SMT lines. As the number of components decreases in the reels we want to

GSM2 spindles Not seen for head

Electronics Forum | Tue Sep 29 09:39:02 EDT 2015 | rgduval

Hey, David, For service, check out 4TechUSA over in Detroit. It's not Chicago, but, you're closer to Detroit up there than I am down here in Houston :) For your issue....do you have access to the UIC Knowledge Base? The first issue I found in the

Re: Hot Air Knife

Electronics Forum | Mon Mar 13 14:41:22 EST 2000 | Boca

By Hot Air Knife I assume (leave it alone Dave F.) that you mean a debridging knife located at the exit end of a wave solder machine. Russ is right, they are not a good substitute for a good process, but once the process (w/o HAK) is developed, it


setup searches for Companies, Equipment, Machines, Suppliers & Information