Electronics Forum: smema connector (Page 1 of 3)


Electronics Forum | Wed Jul 12 17:17:04 EDT 2006 | fordf1502004

I want to thank you for your help. after further investigation into the panasonic machine one our technicians was able to fix the issue. The panasonic machine uses a 5 volt signal and normal smema uses a 24 volt signal. To make these 2 machine talk t


Electronics Forum | Fri Feb 01 18:17:28 EST 2002 | dougt

Is SMEMA still being used? When I go to a guy selling a pick and place machine, should I be overly concerned about having SMEMA connectors on the machine? Do you guys out there use this?

ATI Conveyor Smema Question

Electronics Forum | Tue Jan 08 17:46:38 EST 2008 | swag

If the phone jacks have two conductors in them, I would wire them to standard SMEMA connectors so that the upstream side goes to the middle two SMEMA pins and downstream goes to the outermost two pins. If there are 4 conductors in the phone jacks, y


Electronics Forum | Sun Jan 27 11:28:42 EST 2013 | mdang

Could anyone help to connect a FUJI CP42 machine to a conveyer with stanard SMEMA? CP42 has 2 wire cable and small female connector label SMEMA (Not fit with stanard SMEMA). Thank you for all your help, -Michael

GSM without side conveyors

Electronics Forum | Thu Dec 24 10:07:42 EST 2009 | edwaterfall01

Get two connectors to fit the SMEMA 1 connectors on either end of the machine. Need only two wires on each connector going to momentary contact sw. Input is pins 1 & 2 to switch and output side is pins 3 & 4 to switch. If this doesn't work then ch

Quad IVc power up

Electronics Forum | Mon Apr 13 14:36:18 EDT 2009 | leemeyer

I have seen this problem before. There is a cable that runs from the Quadalign board to the backside of the backplane. It is not secured in any way so it may have come loose in shipping. Open the right side panel on the machine. The Quadalign board


Electronics Forum | Mon Jan 19 15:11:30 EST 2004 | cal

www.smema.org Machine Interface Standard http://www.smema.org/smema1.2.pdf Here is where you can find Machine cable/ connector information as well as timing and interface Schemetic. I would contact Universal for the machine interface connection spe

Re: Big SMEMA Troubles :-(

Electronics Forum | Tue Nov 03 22:11:38 EST 1998 | phillip hunter

| SMTnetters: | | My UIC conveyors aren't working with my: | | �Omniflow 7 Reflow (Mfg 1/95) | �Dek 265 GS | �Philips CSM | | | What can I do? Does anyone have experience with connecting UIC or other conveyors to the above equipment? On the refl

SMEMA manual interface control box schematic

Electronics Forum | Thu Dec 03 14:40:27 EST 2015 | proceng1

When we had a line that ended at an older reflow oven without SMEMA controls, I ran a momentary switch to the two pins in the connector. I push the button and the conveyor pushed the board onto the edge-hold of the oven. As a joke I labelled it "LA

EKRA E5 X20b port

Electronics Forum | Mon Jul 29 10:04:08 EDT 2019 | griinder

I believe the x20 and x21 ports are used for smema. There is a proprietary smema end, that connects to those cables. They almost look like parallel port connectors right?

  1 2 3 Next

smema connector searches for Companies, Equipment, Machines, Suppliers & Information

ISVI High Resolution Fast Speed Industrial Cameras

We offer SMT Nozzles, feeders and spare parts globally. Find out more
SMT Machines

High Throughput Reflow Oven
PCB Handling with CE

High Precision Fluid Dispensers
Encapsulation Dispensing, Dam and Fill, Glob Top, CSOB

High Resolution Fast Speed Industrial Cameras.