smt and connectors

"smt and connectors" search results in the Electronics Forums



337 results found for "smt and connectors" in the Electronics Forums

Order by: Relevancy |   Date

The connector is falling down in the second reflow

Feb 24, 2020 | =0.08g/mm2, make it less than 0.08. And maybe the connector gravity center location is a cause also.

SMT Connectors: Corner legs lifts.

Jan 17, 2020 | Try preheating the connectors

SMT Connectors: Corner legs lifts.

Jan 16, 2020 | Hej back at ya Your connectors could be warping during reflow. Find out by putting a connector on a

SMT Connectors: Corner legs lifts.

Jan 16, 2020 | Hej, we have some connectors placed on our PCB. 2*30legs 0.5 After reflow we detect lifted legs in

SMT Samtec dual edge connector assembly help

Jan 8, 2020 | We have a PCB with the dual sided connector that slides on from the edge and has leads on the top an

200 pin connector reflow

Nov 7, 2019 |

Pin in paste connectors and lead-free questions

Jul 22, 2019 | Hey all! As background, I recently purchased a full SMT line for my company. We have a DEK 265, an

Tyco Hermphrodite connector, mixed up connectors with different surface finishes

Nov 27, 2017 | Hello SMTNet, We had received boards from our CM, some came with a Tin plated finish on the SMT her

DIMM connector with poor solderability

Nov 22, 2016 | Hello Dears, I'm a small CS Engineering at Taiwan.There are some problem on DIMM connector area wit

JST press in connectors

Nov 17, 2015 | I have to figure out how to install a two-pin JST through-hole connector. It is a press-in style. We

Solder wicking up on connector leads

Sep 16, 2014 | We have an issue with solder wicking up the leads/ inside terminations on an SMT connector. The sold

SMT fine picth connector lead oxidize-Throw out rate too high!

Sep 5, 2013 | This connector was designed with gold flash plating and the lead's surface was become dull and some

SMT fine picth connector lead oxidize-Throw out rate too high!

Sep 4, 2013 | SMT fine pitch connector having oxidation on lead and P&P machine keep rejecting the part. Is there

DIMM Connectors

Jul 31, 2012 |

Connector

Feb 27, 2012 | Could anyone suggest where I could get a suitable connector for the 3pin oxggen sensor in the attach

Dual edge mount connector

Sep 6, 2010 | Hi all, Looking for some advice on how to run this component through the SMT process or is it alw

Harwin PC/104 Connectors

Nov 5, 2009 | I would switch to Teka PC104 solder bearing lead connectors. You can reflow them along with your SMT

SMT Connector, Placement Issues

Oct 3, 2008 | On a couple of boards, try remove the pins, let reflow align the connector to the pads

SMT Connector, Placement Issues

Oct 3, 2008 | Change your connector.

SMT Connector, Placement Issues

Oct 3, 2008 | I have a problem with placement repeatability and accuracy on this Samtec connector. The customer w

Fuji feeder E-clips

Apr 9, 2008 |

AMP SMT Connector (PCI)

Oct 26, 2006 | We are having difficulty with thermal deformation of these AMP surface mount connectors. It is a RoH

SMT Edge Connectors

Sep 15, 2006 |

SMT Edge Connectors

Sep 15, 2006 | What kind of connector is it? How does the manufacturer recommend processing their part? We've ha

SMT Edge Connectors

Sep 15, 2006 | We have a new product that uses an SMT edge connector. The process we are using is as follows: -

Harwin SM connector problems

Jul 28, 2005 | Hi guys, Have any of you encountered harwin connector M80-647 in the past? Have you noticed any

Pages: 1 2 3 4 5 6 7

Flux-Free Reflow Soldering

Software for SMT