Electronics Forum: smt and equipment and corp (Page 1 of 9)

Re: Bottom side smt and thru hole

Electronics Forum | Wed May 27 13:42:08 EDT 1998 | Chrys

| R&D is currently designing a board with smt components on both sides of the board. They are adding a 16 pin IC Gull wing. on the bottom side of the board. I have asked for only caps and resistors to be placed on the bottom side. Is there a recommen

Re: Bottom side smt and thru hole

Electronics Forum | Wed May 27 14:35:52 EDT 1998 | Justin Medernach

| | R&D is currently designing a board with smt components on both sides of the board. They are adding a 16 pin IC Gull wing. on the bottom side of the board. I have asked for only caps and resistors to be placed on the bottom side. Is there a recomm

Re: Tabletop pick and place equipment selection

Electronics Forum | Fri May 28 16:03:10 EDT 1999 | Jeff Sanchez

| Has anyone had experience with prototype-scale, table top Placemax and/or Manncorp pick and place equipment? If so, what has been your experience with the machines? Are they reliable? Did they meet all your needs? Which needs didn't they fill?

SMT training classes and start up equipment

Electronics Forum | Mon May 04 16:34:13 EDT 1998 | Denis Desrochers, Manufacturing Engineer

We are just starting out with SMT. I need any and all the information you have. We are looking to start a small to mid range line.

SMT, lead form and trim equipment

Electronics Forum | Mon Jul 20 10:23:29 EDT 1998 | Sherry

Hello friends.... Can someone please point me in the right direction... I will be needing the capability of forming/trimming QFP's on a very low volumn scale in house. So far I've only been able to find one manufacturer and that is Fancort Industri

Re: SMT, lead form and trim equipment

Electronics Forum | Mon Jul 20 13:28:14 EDT 1998 | Chris Fontaine

We regularly form QFP's and FP's (pitches to 20 mil) and have experience with both Knight and Fancort equipment, however most of our experience has been with Knight. Knight Tool has been consistently good, and I've had some sour experiences with Fan

Re: SMT training classes and start up equipment

Electronics Forum | Fri May 22 15:39:59 EDT 1998 | serge

good morning sir i m Belgium and i was responsable for SMT training and maintenance for Alcatel do you believe that i can help you??? | We are just starting out with SMT. I need any and all the information you have. We are looking to start a sma

Re: SMT training classes and start up equipment

Electronics Forum | Fri May 15 09:09:50 EDT 1998 | Earl Moon

| We are just starting out with SMT. I need any and all the information you have. We are looking to start a small to mid range line. I provide consultation for these requirements. Please contact if interested. Sincerely, Earl Moon pod@ix.netcom.com

Re: SMT training classes and start up equipment

Electronics Forum | Mon May 04 21:35:25 EDT 1998 | Dave F

| We are just starting out with SMT. I need any and all the information you have. We are looking to start a small to mid range line. Denis, You should pursue the following SMTNet thread on this topic: Posted by Igor Kostyuk on April 22, 1998 at 16:57

Re: SMT training classes and start up equipment

Electronics Forum | Wed May 06 10:20:21 EDT 1998 | SMT-ASSY

Good morning, We would like to offer our services. SMT-ASSY is a training facility (Located in Dorval, Montreal area) which can introduce your workforce to SMT and the workmanship required to obtain quality products. We have attached our brochure in

  1 2 3 4 5 6 7 8 9 Next

smt and equipment and corp searches for Companies, Equipment, Machines, Suppliers & Information

KingFei SMT Tech
KingFei SMT Tech

Main Products: 1. Original new and Original Used SMT/AI Spare Parts. 2. SMT Equipments And Related Machine( SMT Calibration, SMT Feeder Carts,Conveyer etc.) 3. Maintenace and Repair Service Pre-Sales Service Provide details ab

Manufacturer's Representative / Manufacturer / Equipment Dealer / Broker / Auctions / Consultant / Service Provider

Building A, Jiepeng Square, Fuyong
Shenzhen, 30 China

Phone: 0755-33578694