Electronics Forum: solder and ball and approved (Page 1 of 17)

BGA ball and PCB pad

Electronics Forum | Wed Feb 18 12:42:43 EST 2004 | babe

OK, if the sphere of the ball and the paste on the pad are both eutectic, 63/37 then the paste will reflow first causing a drop of the component, after which the spheres will reflow causing a double drop and a good intermettalic. You can see this by

BGA ball and PCB pad

Electronics Forum | Fri Feb 20 13:01:26 EST 2004 | Jay

First, it depends on the alloy composition of the solder. As you might know, eutectic Sn/Pb solder has the lowest melting point among available conventional solder systems. (except those based on Sn-In and Sn-Bi systems.) For example, 63Sn/37Pb - 183

BGA ball and PCB pad

Electronics Forum | Fri Feb 13 11:19:07 EST 2004 | Evtimov

Hi Bryan The answer is in the paste compozition. Balls of the BGA are usually made by eutetic solder paste.

BGA ball and PCB pad

Electronics Forum | Thu Feb 12 10:19:46 EST 2004 | Bryan

Hi all, These days our customer asks us to figure out ,during reflow,the BGA ball and solder paste,which will first melt? I think it's very hard to get the rusult.coz I think it'll vary at diffrent part of the BGA,and how can this affect the perf

BGA ball and PCB pad

Electronics Forum | Fri Feb 13 11:46:23 EST 2004 | Jack

Is your customer trying to reduce voiding? If the device is using Sn90 / Pb10 and the paste is Sn63/Pb37 the board will melt first. However, if both solders are 183C eutectic, it's a tossup? PCB design, copper weight, bga type (pbga, micro bga, Tbg

BGA ball and PCB pad

Electronics Forum | Fri Feb 27 11:33:32 EST 2004 | Bryan

Very strange question,but interesting.Is there anyone who have conducted any experiments to figure out the results?I made a profile board,one thermal couple on pad and other one drilled into the ball of BGA.the 2 points are perpendicular to conveyor

BGA ball and PCB pad

Electronics Forum | Tue Feb 17 04:52:13 EST 2004 | John W

There's normally a number of reasons people want to know what melts 1st, 1 - to see if you know, 2 voiding issues - whole can of worms 3 device alignment. One of our collegues has said that most balls are Eutectic, that's in fact not totally correct.

solder balls and flux

Electronics Forum | Tue Feb 29 10:14:02 EST 2000 | Robert Hartmann

My company is just getting into the flip chip packaging arena. We are putting in a prototype/small volume wire bond PBGA line. We have some questions with regard to choosing solder balls and cleaning of flux. 1) Is there a formula for the shrink

solder balls and flux

Electronics Forum | Tue Feb 29 10:14:02 EST 2000 | Robert Hartmann

My company is just getting into the flip chip packaging arena. We are putting in a prototype/small volume wire bond PBGA line. We have some questions with regard to choosing solder balls and cleaning of flux. 1) Is there a formula for the shrink

mask finish and solder balling

Electronics Forum | Fri Feb 19 14:43:46 EST 1999 | Nithy

We are in the process of getting into no-clean paste and fluxes. One important issue in this is sodler balling. I have heard some people say that having a matte finish would help in having lesser solder balls and that the solder balls would not be

  1 2 3 4 5 6 7 8 9 10 Next

solder and ball and approved searches for Companies, Equipment, Machines, Suppliers & Information

Global manufacturing solutions provider

World's Best Reflow Oven Customizable for Unique Applications
2024 Eptac IPC Certification Training Schedule

Stencil Printing 101 Training Course
2024 Eptac IPC Certification Training Schedule

High Precision Fluid Dispensers