Electronics Forum: solder and paste and roll and height (Page 1 of 3)

Solder paste height and metal squeegees

Electronics Forum | Fri Apr 20 16:05:17 EDT 2001 | gcs

We always reduce side to side, EXAMPLE: 12 mil width reduced to .010". Do you guys check viscosity ? Also maybe your guys are appling to much pressure on the sqweegee blades.

Solder paste height and metal squeegees

Electronics Forum | Fri Apr 20 11:05:23 EDT 2001 | gcs

Just a bullet! My results are, .005" stencil thickness should measure between .0055" - .006" if your pressure is correct, metal blades and snap-off is set up correctly. Do you have aperture reductions at the QFP locations "typicial industry standard

Solder paste height and metal squeegees

Electronics Forum | Fri Apr 20 15:27:00 EDT 2001 | jimlew

We do some aperture reductions - but it's not the 10% i'm accustomed to. Looks like it should be more than we currently do (I think we do 10% of length, but no width). Don't think we have a slumping problem, and we're not doing snap-off, only contact

Solder paste height and metal squeegees

Electronics Forum | Fri Apr 20 08:41:56 EDT 2001 | jimlew

For those of you out there, like myself who are still using 2-d to measure paste ht, I have 2 questions. 1. Typically, what tolerance are you applying to your ht? +- 1 mil, or what? 2. Are you using metal squeegees, and if so, have you found that squ

Volume and average height of solder paste after printing machine

Electronics Forum | Thu Oct 02 01:47:57 EDT 2008 | myleb

I'm new to SMT. Now, i'm making program for SPI machine to inscpect for solder paste of SP60-MU. I think this is a very good printer but some times, my program shows only 50-60% of volume transfer; and the average height is very high: nearly 200 pct.

Volume and average height of solder paste after printing machine

Electronics Forum | Thu Oct 02 17:00:44 EDT 2008 | davef

Is that accurate? If so, what are your aspect & area ratios? [Similar to the JerryS comment above.] * You say, � � and the average height is very high: nearly 200 pct.� => Our troop can make paste that height too. They snap the stencil-off a fast as

Volume and average height of solder paste after printing machine

Electronics Forum | Thu Oct 02 12:22:26 EDT 2008 | JerryS

Hello Ok there is not much info here. What you have to mae sure of is several key factors. 1. Have you entered the correct stencil thickness. 2. Are you using the stencil gerber (not the paste layer) The paste layer is usually not adjusted for ap

SMT Solder paste and wave flux evaluation

Electronics Forum | Fri Jan 28 12:29:01 EST 2005 | Bob R.

We use the exact same method Chunks outlined for evaluating just about anything we're going to roll out worldwide, whether it's a material or a machine. List your factors (print speed, solder spread, etc), assign each a weight, evaluate each paste a

SMT Solder paste and wave flux evaluation

Electronics Forum | Fri Jan 28 12:18:32 EST 2005 | Chunks

Your best bet is to do a decision making matrix. Each company has so many different criteria�s it's hard to pick out which one might be important to yours. Simply pick out your top 5 paste manufactures. Next decide what your "Eliminators" are - th

Solder Paste and Stencils

Electronics Forum | Tue Oct 12 10:24:50 EDT 1999 | Jose RG

Hi, We are in the way to evaluate different solder pastes, improve our solder paste incoming inspection steps, re-define our stencil requirements and the following questions are open. Two questions, 1- Is anybody using/requiring 1000 Kcps or more

  1 2 3 Next

solder and paste and roll and height searches for Companies, Equipment, Machines, Suppliers & Information

Reflow Ovens

PCB Assembly Supplies - ONLINE STORE
MSD Dry Cabinets

Want to know where to find the best AOI system? - Read testimonials.
smt assembly equipment manufacturer

Private label coffee for your company - your logo & message on each bag!