Electronics Forum: soldermask and smd (Page 1 of 13)

seperation of soldermask and pcb

Electronics Forum | Tue Mar 25 09:35:28 EDT 2014 | emeto

Have you tried to bake the boards before you process them?

seperation of soldermask and pcb

Electronics Forum | Tue Mar 25 10:31:05 EDT 2014 | sara_pcb

The boards are baked for 2 hours at 120 deg C Regards, R.Saravanan

seperation of soldermask and pcb

Electronics Forum | Tue Mar 25 08:29:33 EDT 2014 | sara_pcb

Please refer the attached jpegs, The problem is noticed after reflow soldering followed by conventional through hole soldering. Flux used one is MIL Std. Brush cleaning in IPA is followed after each soldering step. regards, R.Saravanan

seperation of soldermask and pcb

Electronics Forum | Tue Mar 25 11:25:18 EDT 2014 | horchak

The first impression I get is that the mask was applied over dirty or contaminated copper. What is the trace and land finish on the PCB? You also appear to have a wetting problem.

seperation of soldermask and pcb

Electronics Forum | Tue Mar 25 11:43:48 EDT 2014 | sara_pcb

It is Solder Mask on Bare copper, The land finish is HASL as per MIL-PRF-55110G which accepts trace of HASL as acceptable. Wetting is acceptable. regards, R.Saravanan

seperation of soldermask and pcb

Electronics Forum | Tue Mar 18 11:53:58 EDT 2014 | sara_pcb

Our contract manufacturing agency have procured pcbs from approved vendor. After assembly we found solder mask separated from the PCB on the epoxy area as patches. The top side is intact. also over the pcb tracks, the mask got damaged. In what c

seperation of soldermask and pcb

Electronics Forum | Wed Mar 19 08:38:13 EDT 2014 | davef

I can't picture much of what you're saying, not for nothing, I'm just not connecting. During assembly, solder mask can affected by heat and chemicals. Typically this would be during: * Soldering * Cleaning I will tell you this: Not to defend assem

seperation of soldermask and pcb

Electronics Forum | Tue Mar 25 13:55:05 EDT 2014 | horchak

Ok lets put it this way. If the PCB house used a high quality mask and properly applied it to a properly cleaned surface and properly cured it, then as Dave stated above there are only two things that can destroy it. Excessive heat and overly aggress

smd lead forming and cutting

Electronics Forum | Tue Aug 10 06:58:48 EDT 2004 | dka123

dear all, kindly guide me for the use of space electronics hardware assembky of PQFPs and Cqfps, how to form the flat pack leads, bend for 240 pins of 20 mil pitch and what are the Mil standards for them.how to cut the lead guards.can we use FP5 elit

Quick Frame and Dek 265GS

Electronics Forum | Wed May 20 07:13:15 EDT 1998 | smd

Does anyone use the "Quick Frame" with their Dek printer? The threads on the screws keep stripping, so we thought maybe we'd send our frames to a machine shop for heftier screws. Has anyone done this? Is there a better way? Isn't it weird how Alpha k

  1 2 3 4 5 6 7 8 9 10 Next

soldermask and smd searches for Companies, Equipment, Machines, Suppliers & Information

Best SMT Reflow Oven

High Throughput Reflow Oven
One stop service for all SMT and PCB needs

Training online, at your facility, or at one of our worldwide training centers"
PCB Handling with CE

World's Best Reflow Oven Customizable for Unique Applications
SMT feeders

Have you found a solution to REDUCE DISPENSE REWORK? Your answer is here.
Electronic Solutions R3

Low-cost, self-paced, online training on electronics manufacturing fundamentals