Electronics Forum: solenoid (Page 1 of 7)

Fuji CP lube

Electronics Forum | Thu Sep 13 11:01:39 EDT 2007 | cyber_wolf

Fuji specs out Omega 66 grease for the solenoid sliders on older CP machines. These solenoids run hot. Its interesting to me that this grease is designed for extremely low temperature applications. Whats up with that ? http://www.omegaoil.co.jp/ind

CP43 Solenoid Station 3 Stopper CW

Electronics Forum | Wed May 26 11:16:03 EDT 2010 | cyber_wolf

It is totally normal for these solenoids to run very hot. Hot enough to fry spit. I wouldnt pay any attention to it

Who is the Mydata TP series expert ?

Electronics Forum | Tue Nov 04 07:38:51 EST 2008 | jdengler

SrTech, I do not know Mydata's but I had a problem with a solenoid for a nozzle changer that just didn't seem to be strong enough. Finally found a partial break in the wire. I seemed like this acted a resistance to the current flow and did not all

CP43 Solenoid Station 3 Stopper CW

Electronics Forum | Wed May 26 04:46:13 EDT 2010 | mmjm_1099

ALl - I need some feedback why a solenoid on station 3 is getting excessively hot. I have another line with the same setup but is not getting as hot. I have tested out voltage and see nothing that is triggering me there is an overvoltage. Any feedbac

FUJI CP4-3 Nozzle Change Alarm

Electronics Forum | Thu Jul 31 14:07:44 EDT 2014 | kurtiss

I found a bad solenoid and replaced it solenoid 15 on station 11. The machine is still erroring out. I also checked the holders and sensors and they seem to be ok. This error occurs when ever the machine tries to change nozzle sizes on any holder. T

MPM AP/A Screnn Printer - Dispense Pinch Disable

Electronics Forum | Mon Sep 02 15:41:47 EDT 2013 | aemery

Mr Duckmann2000. Where is the leak??? Is it up on the dispenser behind the printhead? If so the simpliest thing to do, assuming you are not using the dispenser, is to cut the incoiming air tubing to the dispense pinch, fold it over and ty-wrap it.

Pulse Driven Variable Power

Electronics Forum | Fri May 14 15:28:39 EDT 2010 | timryder

I have an application I'm trying to solve which would allow me to vary voltage going to an Electric Solenoid at 24v ~3.0amps DC. What I want to do is create a device to vary the voltage going to the Solenoid using a pulsed digital input. I have a mot

Re: Gold Finger Wear

Electronics Forum | Wed Dec 20 17:33:00 EST 2000 | Travis Slaughter

I don�t have the answer for you but it would not be difficult to make a fixture to find out. Combine a counter, pneumatic cylinder, and a solenoid in such a way to do the job for you. Cylinder pushes the card into the connector, when contact is made

Fuji Bare Board Loader PARTS

Electronics Forum | Fri Jan 18 07:01:41 EST 2008 | cyber_wolf

Hi, The solenoid that sits on top of the vacuum generator on my Fuji bare board loader is croaking slowly. Fuji will only sell me the entire generator assy. which cost more than I paid for the loader. The only markings on the solenoid are DC24V 540

Universal 6346A Radial Lead Sequence Bad I/O Card?

Electronics Forum | Mon Apr 10 15:34:53 EDT 2017 | mrich208

Hey Jerry, The valve that sends air to the head of the inserter does not close when you press the "Interlock" button. If you press on the end of the solenoid with a screewdriver to force it the air makes it to the head. If doesn't seem like it is tr

  1 2 3 4 5 6 7 Next

solenoid searches for Companies, Equipment, Machines, Suppliers & Information