Electronics Forum: sp-200 (Page 1 of 2)

Screen Printers

Electronics Forum | Thu Nov 28 09:42:51 EST 2002 | Claude_Couture

MPM SP200 are nice. Visual alignment with cameras. Get the one with dual head if you want metal squeegees. We have produced boards with .020" fine pitch with very good results. Unfortunatly, MPM does not sell those anymore, so you have to hunt for a

Screen Printers

Electronics Forum | Mon Dec 02 08:39:07 EST 2002 | pjc

The MPM SP200 was replaced by the model SPM around 1994. They also have the model UP100, which is from the SMTech purchase. The UP100 is the low-end MPM semi-automatic. Information on the SPM & UP100 can be found at http://www.cooksonee.com

Manual Stencil Printers

Electronics Forum | Fri Nov 11 11:02:23 EST 2005 | russ

i would look at an SPM from MPM(speedline) or an SP200 from Europlacer (speedprint not speedline) We have used both of these machines with great success from 16mil pitch qfps to .5mm pitch uBGAs.

20 mil qfp bridging

Electronics Forum | Thu Aug 12 18:43:49 EDT 1999 | Wayne S.

Hello Having a problem with bridging on 20mil pitch qfp, only on the lead groups where squeegee goes over width of apertures. Using MPM sp-200 semi-auto, chem-etch stencil, 9-10mil width opening 100 durometer blade. Getting "tails" on deposits. Trie

Re: 20 mil qfp bridging

Electronics Forum | Thu Aug 12 20:17:12 EDT 1999 | Kelly Morris

Hello Having a problem with bridging on 20mil pitch qfp, only on the lead groups where squeegee goes over width of apertures. Using MPM sp-200 semi-auto, chem-etch stencil, 9-10mil width opening 100 durometer blade. Getting "tails" on deposi

SpeedPrint SP200e - Help please !

Electronics Forum | Wed Feb 23 22:56:46 EST 2011 | jeffr

When I enter the "Setup Table Contact" menu, then press "Load PCB" the squeegee head should move to a mid position that I can set the squeegee height, but instead it moves the squeegee head to the front limit and displays a red error message about th

Solder Stations that meet J-STD-001 Rev E

Electronics Forum | Tue Nov 15 16:31:04 EST 2011 | pcbrown

Can anyone tell me if the Metcal SP200 solder station meets the J-STD-001 Rev E requirement of holding a tip temp of +/-9F at rest? I am in a fight with an auditor over this. These irons do not require calibration but I need to know if they meet J-ST

Printers - DEK vs Speedprint

Electronics Forum | Mon Jan 30 06:29:44 EST 2006 | robls

We are a Contract Manufacturer in South Africa. We currently have a Speedprint SP200AVI fully automatic printer with 2D vision etc etc. We require a second fully automatic printer and are busy evaluating a DEK Horizon 03i. We have found good points

Re: 20 mil qfp bridging

Electronics Forum | Fri Aug 13 12:52:17 EDT 1999 | Steve Schrader

Hello Having a problem with bridging on 20mil pitch qfp, only on the lead groups where squeegee goes over width of apertures. Using MPM sp-200 semi-auto, chem-etch stencil, 9-10mil width opening 100 durometer blade. Getting "tails" on deposi

Re: 20 mil qfp bridging

Electronics Forum | Tue Aug 17 10:41:13 EDT 1999 | Steve A

Wayne, Sounds like a gasketing problem. When the horizontal apertures are bleeding but not the vertical apertures. Could be poor underside support, HASL miniscus issues, masking or plugging issues, but what many people do not account for is that t

  1 2 Next

sp-200 searches for Companies, Equipment, Machines, Suppliers & Information