Electronics Forum: spots and under and solder and mask (Page 1 of 2)

kapton dots and liquid solder mask

Electronics Forum | Wed Aug 10 11:57:16 EDT 2005 | pr

Is the peelable mask (put on by the boardhouse) flat on the surface of the pcb? If so can you tell me the material name, so maybe I can find a picture? We have to print adhesive on the board, so the mask has to be flat. That is why Kapton from the b

kapton dots and liquid solder mask

Electronics Forum | Tue Aug 09 13:25:24 EDT 2005 | pr

From what I can gather, the annular rings are used for grounding when these boards are put in housings. A screw goes through the hole and is torqued down. If there is excess solder on the annular ring, the screw doesn't seat properly. The pallets cov

Reflow soldering problems and traces under component

Electronics Forum | Tue Jul 19 08:26:46 EDT 2016 | pavel_murtishev

Aleksander, The answer is no. Solder deposit being printed is 80um-150um in height depending on PCB design what is two times higher than any track covered by solder mask. Molten solder will merely center the component. QFNs are prone to soldering

Reflow soldering problems and traces under component

Electronics Forum | Mon Jul 18 12:25:30 EDT 2016 | oleksz

Some people involved in PCB assembly process claim that SMD components reflow soldering problems are often caused by traces running under a component. According to this claim, trace (or any copper) covered by solder mask and placed under SMD componen

Reflow soldering problems and traces under component

Electronics Forum | Mon Jul 18 12:24:53 EDT 2016 | oleksz

Some people involved in PCB assembly process claim that SMD components reflow soldering problems are often caused by traces running under a component. According to this claim, trace (or any copper) covered by solder mask and placed under SMD componen

SOT-223 Flux trapped under part and lifting off pads

Electronics Forum | Thu Sep 30 11:30:46 EDT 2010 | babe7362000

Take a few parts from the reel and look close at > the parts to make sure the bottom surface of the > leads is below the bottom surface of the body. Yes I did that and they are below the body. I found the problem I think. The solder mask is abo

Blistering and delaminating boards

Electronics Forum | Thu Sep 20 07:18:42 EDT 2018 | proceng1

Has anyone else been experiencing this lately? We have had a rash of boards that come in properly vacuum sealed. We store them in the hot room until we are ready to build, and we get bubbles under the solder mask. We've had 4 different jobs, all di

Heat guns and component damage

Electronics Forum | Wed Feb 01 08:12:04 EST 2006 | Chunks

OK, this is easy. You say HIGH fall out, so I can assume 25 or 50%? If so, run 10 without the heat gun and 10 with. This should show you if the heat gun process is the cause or not. If the relay is a surface mount, hand solder them on. If it's a

Re: Green coating and through-hole plating

Electronics Forum | Thu Aug 13 12:55:46 EDT 1998 | Dave F

| Hi, can you please tell me how to make green coating and through-hole plating of PCB? Thanks! | Xingsheng Xingsheng: Welcome. Bible on PCB fabrication: Printed Circuits Handbook, Clyde Coombs, McGraw-Hill Web resources: http://www.pwbrc.org/ a

Re: Green coating and through-hole plating

Electronics Forum | Fri Aug 14 07:27:42 EDT 1998 | Earl Moon

| | Hi, can you please tell me how to make green coating and through-hole plating of PCB? Thanks! | | Xingsheng | Xingsheng: Welcome. | Bible on PCB fabrication: Printed Circuits Handbook, Clyde Coombs, McGraw-Hill | Web resources: http://www.pw

  1 2 Next

spots and under and solder and mask searches for Companies, Equipment, Machines, Suppliers & Information

Circuit Board, PCB Assembly & electronics manufacturing service provider

High Precision Fluid Dispensers
Encapsulation Dispensing, Dam and Fill, Glob Top, CSOB

High Throughput Reflow Oven
Fluid Dispensing, Staking, TIM, Solder Paste

Best Reflow Oven
SMT feeders

World's Best Reflow Oven Customizable for Unique Applications


Internet marketing services for manufacturing companies