Electronics Forum: srt pickup nozzle (Page 1 of 18)

Head doesnt pickup nozzle from ATC (+2mm are needed)

Electronics Forum | Wed Aug 10 09:56:09 EDT 2022 | jojoled

Hi guys, from certain time (not sure, but it could be power down last week) none of the 2 heads can succesfully pickup nozzle from ATC (after startup calibration is done, but in the calibration sequence the ATC height is not measured, it just calibra

CP6 pickup errors

Electronics Forum | Fri Feb 25 16:34:53 EST 2005 | jimmyb

In your PDs you must specify a single nozzle size. Meaning don't assume that entering nozzle size max=1.3 and nozzle size min=1.3 forces the machine to use a 1.3. Nozzle size min is not used in the CP6 software (it only uses nozzle size max), there

FLexJet pickup problems

Electronics Forum | Fri Apr 29 19:39:58 EDT 2011 | jbaez1

Hi, have somebody out there experienced problems picking up passive components with flexjet head FJ7P?? Just 1 nozzle-spindle is failing, trying to pickup a resistor,cap or diode; I have already changed nozzle tip, nozzle adaptor including springs,va

CP6 pickup errors

Electronics Forum | Fri Feb 25 23:26:27 EST 2005 | siverts

Good point [engguy], and another thing; if you are using 1.3mm nozzle on a feeder that has a shutter opening of 1.0mm = problem. You could even damage the nozzle. So the main questions remain....

CP6 pickup errors

Electronics Forum | Mon Feb 28 08:34:46 EST 2005 | Alex

Good advises thanks. I'll go thru all nozzles and vacuum check today and tell the programer about PD's and nozzle vs shutter. Should I check at the same time all the vacuum filter ? For the placement test, we use the same feeder at the same position.

Quad IVc pickup problem

Electronics Forum | Tue Apr 26 07:37:59 EDT 2011 | leemeyer

Have you performed the camera to nozzle calibration ? I can send you instructions for this if you need them.

Quad IVc pickup problem

Electronics Forum | Tue Apr 26 09:46:27 EDT 2011 | veeckm

Thanks for the reply. I have not performed the camera to nozzle calibration. Is this the same as the calibration of the vu3 camera in the manual? If you would please give me your instructions, any help is appreciated.

Quad IVc pickup problem

Electronics Forum | Tue Apr 26 10:14:06 EDT 2011 | leemeyer

The camera to nozzle offset calibration requires that you modify some of the mod codes once the offsets are calculated. This is not part of the VU3 calibration. Send me your email address so that i can attach a copy of the manual for you.

Quad IVc pickup problem

Electronics Forum | Mon May 09 16:32:05 EDT 2011 | veeckm

I got the camera nozzle offset corrected but after the machine runs for a while the offset will drift and its out the specs I set it to. Any help is appreciated.

FLexJet pickup problems

Electronics Forum | Fri May 13 09:11:01 EDT 2011 | vickt

And does this problem spindle exchange nozzles in the changer without issues? When was the last time the clutches were replaced? thx

  1 2 3 4 5 6 7 8 9 10 Next

srt pickup nozzle searches for Companies, Equipment, Machines, Suppliers & Information

Surplus to the Ongoing Operation of Global EMS Provider ITAR-Certified Low-to-Mid Volume Surface Mount Shop (2) ’17 ASM E Placement Machines w/ (500+) Feeders Ersa – Yxlon -- Dage – Ekra – BTU – Much More!  used equipment auctionm_source=SMTnet&utm_medium=digitalads&utm_campaign=PTC

High Resolution Fast Speed Industrial Cameras.
PCB Handling Machine with CE

World Source Equipment: Used equipment sale. Hundreds of items on sale.
MSD Dry Cabinets

Reflow Soldering 101 Training Course
one-stop for smt solution

Training online, at your facility, or at one of our worldwide training centers"