Electronics Forum: ssop and pad and width (Page 1 of 2)

IP1 and SSOP28

Electronics Forum | Tue May 18 16:40:22 EDT 2010 | m79d

I am having some problems getting the IP1 to place a SSOP28 package,pitch 0.65mm lead width 0.3mm. I am selecting computer vision 012 (tried 011) and vision type 100. EL data was put in looking at the datasheet and also measuring the device. Have tri

IP1 and SSOP28

Electronics Forum | Tue May 18 21:43:02 EDT 2010 | ashley

Hello mickd, 1) The EL data & Vision_type is NOT necessary when using MCS30 for IP1 machine. note : your input of the above might have cause confusion during VP, hence the OS error. 2) I would suggest the following... 2a) lower the Lead_check_are

Pad and Stencil Design

Electronics Forum | Mon Sep 17 16:03:13 EDT 2001 | jschake

The results from an experiment comparing 27 different combinations of pad dimensions concluded that the pad design with 15 mil pad length, 12 mil pad width, and 9 mil pad separation produced the best assembly yields. A 5 mil thick laser cut stencil

Component Database and Placement List

Electronics Forum | Mon Oct 23 06:50:06 EDT 2017 | spoiltforchoice

For package shapes/names I would recommend using manufacturer names. This is much safer than coming up with descriptive names like QFN32_5x5 as there are multiple 5mm 32Pin QFN shapes even when pitch is the same, this makes it safer to use a name in

Solder Paste and fine pitch components

Electronics Forum | Wed Sep 18 12:35:56 EDT 2002 | stepheno

Fourth - > back to design of PCB. Are there solder dams of > mask between the pads? If yes, that helps. If > not, pay close attention to stencil aperture > width and be sure that the aperture deposits less > paste by 1-2 mils per pad, centered o

PCB land pattern for RC0402 and CC0402

Electronics Forum | Wed Sep 24 04:18:12 EDT 2008 | gang

we have some problems in soldering joints such as insufficient solder and misalignment on some RC0402 and CC0402,i don't have a pic here. our SMT enginner doubts the PCB land pattern is at the fault.here is what we measured results.pad length:0.9mm,

Solder Paste and fine pitch components

Electronics Forum | Wed Sep 18 10:06:30 EDT 2002 | Bob M

I place 15-20 mil a lot. You need to look at your pad to apature reduction. Your stencil thickness. The type of paste your using. We use 2-5 mil reduction on each side as a general rule on fine pitch. This varies depending on pad width. We also use 5

Solder Paste and fine pitch components

Electronics Forum | Wed Sep 18 12:31:16 EDT 2002 | dragonslayr

My suggestion is to conduct a Design For Manufacturing (DFM)study on the assembly in question. Pay particular attention to the pad sizes, component lead dimensions and satisfy yourself that those two factors are correct. Given that pads match compone

Foam fluxer maintenance, storage and cleaning

Electronics Forum | Mon Nov 09 09:44:22 EST 2015 | davef

Purpose. This describes setting-up a wave soldering system set-up for a new assembly design or checking a wave solder machine operation with a test board. Applicability. To be used for new design printed circuit assembles and during machine accept

Re: Epoxy printing and wave soldering on 0603 and 0402 components

Electronics Forum | Wed Jul 14 21:34:16 EDT 1999 | karlin

| | | | | Hi, | | | | | | | | | | I need some urgent informations on stencil design guidelines on how to perform epoxy printing on 0603 and 0402 components. Could anyone help? ( Reflow process is not possible because of some other constriants) | |

  1 2 Next

ssop and pad and width searches for Companies, Equipment, Machines, Suppliers & Information

Non-heated dispensing system

Training online, at your facility, or at one of our worldwide training centers"
One stop service for all SMT and PCB needs

MSD Dry Cabinets
PCB Handling Machine with CE

High Speed Precision In-Line SPI System - Mirtec MS-11


Training online, at your facility, or at one of our worldwide training centers"