Electronics Forum: strong (Page 1 of 45)

AOI - Whether Vi Tech or Omron

Electronics Forum | Wed Dec 02 12:50:25 EST 2009 | ecyor

both are strong in their unique speciality. it depends on what you would like to specialise in capturing.

Re: Paladium Pillows and Bad Dreams

Electronics Forum | Mon Feb 23 13:25:21 EST 1998 | Steve Gregory

Steve - you must not work to IPC class 2 or 3 requirements. If the solder is "pillowed" around the lead, I would strongly suspect a wetting problem. Most of the Paladium leads I see soldered have a strong line of demarcation but no pillowing. Hav

Router bit for cutting aluminum PCB

Electronics Forum | Thu Jul 07 23:43:31 EDT 2022 | tey422

We been using the Sayaka SAM-CT23Q machine to depanel PCB, it was fine. But now, we have to depanel the Aluminum PCBs the current bits from IMPEC we are using are not strong enough (1.5x8.0 diamond downcut). Need to find much strong bit or bits des

Re: unsoldered smt board assy shipping

Electronics Forum | Thu May 18 16:44:44 EDT 2000 | Travis Slaughter

You should be able to do it with the proper epoxy. I found one several years ago that was so strong during the sheer test the board delaminated and gave before the glue. I did not go with it for rework reasons, that�s something you might want to th

Anyone reviewed Cost of SMT Quality Model?

Electronics Forum | Mon Apr 21 13:33:35 EDT 2003 | scifi97

I am just curious if anyone has read the Cost of SMT Quality article by Joe Vilella (CEO of Vectron) in the April 1 issue of Electronic Business magazine http://www.eb-mag.com (You can obtain the model from Joe at joev@vectroninc.com) I have review

Cracked Capacitors

Electronics Forum | Fri Sep 09 07:55:08 EDT 2005 | davef

This pattern indicates flex cracking due to excessive bending of the board or fixture after soldering. Ceramic is strong in compression, but weak in tension. When bending causes damaged parts, look at: * Board flexes, ceramic is strong in compressio

Solderability

Electronics Forum | Mon Oct 31 09:35:59 EST 2005 | Slaine

Hi as this has a gold flash the nickle should be active an not require strong fluxes, i would suggest either your not getting enough heat into it (unlikely if your seeing dewetting). or that you have a plating problem the nickle has oxidised before

DEK 265 motor com error, axis 1,2,3 fatal error

Electronics Forum | Thu Sep 01 08:30:54 EDT 2016 | bukas

Certainly possible CPU board issue; but check PC > power supply, that all DCV are present and > strong. > > www.dekhead.com > Certainly possible CPU board issue; but check PC > power supply, that all DCV are present and > strong. > > http:/

Looking for 'Chipbonder' glue for SMT

Electronics Forum | Thu Oct 26 11:41:53 EDT 2023 | proceng1

We currently use Loctite 348 chipbonder to secure large parts that will hang under the board when reflowing the second side. Rework has been complaining that they sometimes have to remove those parts to make repairs and it's difficult to remove them

Re: wave solder bridges

Electronics Forum | Tue Aug 01 16:33:08 EDT 2000 | Ron Lasky

Jason, it looks like you have several options that have strong promise of working. I suggest you perform a designed experiment to find/optimize the best solution with these suggested approaches. Ron

  1 2 3 4 5 6 7 8 9 10 Next

strong searches for Companies, Equipment, Machines, Suppliers & Information

thru hole soldering and selective soldering needs

Training online, at your facility, or at one of our worldwide training centers"
ISVI High Resolution Fast Speed Industrial Cameras

High Resolution Fast Speed Industrial Cameras.
High Throughput Reflow Oven

Nozzles, Feeders, Spare Parts - Siemens, Fuji, Juki, Yamaha, etc...
Pillarhouse USA for Selective Soldering Needs

High Throughput Reflow Oven


"回流焊炉"