Electronics Forum: tens and unit (Page 1 of 8)

COB and wire bond

Electronics Forum | Mon Jun 03 12:51:17 EDT 2002 | V.RAMANAND KINI

We are doing COB operations for nearly ten years. Pls. write to me if you need info on m/c selection, type of PCB, plating etc., Thanks V.RAMANAND KINI...03.06.02

Wave flux and profiling

Electronics Forum | Sat Dec 16 08:23:11 EST 2006 | pr

The "Wave optimizer" is a little pricey but is easy to use, gives instant feedback (display on the unit as opposed to hooking it up to a computer)and will give feedback on the waves, as well as preheat. They will send you a unit to trial for a week o

UPS and ROHS Compliance

Electronics Forum | Thu Jan 26 18:19:02 EST 2006 | GS

Again talking about Tsunami ROHS......... What about UPS units for small or large Power, do they must be ROHS compliance or not ? Regards.................GS

Wave and Reflow Profiler

Electronics Forum | Tue Feb 19 07:44:41 EST 2008 | tonyamenson

So just to clarify.... If i bought a KIC 2000 I could run that one unit over both my waves and through both my ovens (leaded and lead-free)? Or would I need additional equipment to use it on the wave?

Manncorp Pick and Place

Electronics Forum | Mon Aug 04 12:28:42 EDT 2014 | dyoungquist

Mydata (recently changed name to Micronic) will be more expensive than Manncorp but from my experience using Mydata, they are well worth the money. Tech support (in the USA at least) is very good if you go through them to buy the machines. You can

SMT Adhesive and Other

Electronics Forum | Fri Feb 08 03:54:37 EST 2008 | muarty

I would think that you could quite easily use 0.6mm I/D nozzles even when using a hand syringe. As you say you are only using this for larger devices to prevent them from falling off. I am sure there are very reasonably priced small compressed air un

SMT Adhesive and Other

Electronics Forum | Mon Feb 11 13:41:12 EST 2008 | sliebl

We use EFD pneumatic dispensers. Several are second hand from our favorite online auction site. I just checked on there and there are 3 units currently less than $50. Have the bean counters where you work get you one. Tell them your hand hurts from u

Tp9 and Tp9 ufp

Electronics Forum | Thu Oct 27 20:37:49 EDT 2011 | tech1

the calibration error sounds like it is an electrical verifier issue. Are you testing parts before you place them? It could be that your centering electrodes are worn or dirty, or it could be the ribbon cables from the centering unit. If you are usin

UPS and ROHS Compliance

Electronics Forum | Thu Jun 15 14:42:35 EDT 2006 | Tim Austin

You wrote "The directive does not state anything about generating electricity"; actually it does do exactly that: Equipment, "which is dependent on electric current or electromagnetic fields in order to work properly, and equipment for the GENERATIO

Material Ageing and Storage

Electronics Forum | Thu Feb 22 10:32:25 EST 2001 | CAL

SCOTT- We do solderability testing for the electronics industry using a Multicore and Kester Wetting Balance testers. The standards we test to is IPC J-STD 002 for components and J-STD 003 for PCBs. There is also a system called SERA we co-developed

  1 2 3 4 5 6 7 8 Next

tens and unit searches for Companies, Equipment, Machines, Suppliers & Information

Software for SMT

High Precision Fluid Dispensers
2023 Eptac IPC Certification Training Schedule

High Throughput Reflow Oven
thru hole soldering and selective soldering needs

Software programs for SMT placement and AOI Inspection machines from CAD or Gerber.
PCB Depanelizers

Private label coffee for your company - your logo & message on each bag!