Electronics Forum: theta motor (Page 1 of 5)

Mydata theta problem

Electronics Forum | Fri Sep 18 10:58:04 EDT 2015 | adventurelights

Thanks, have checked the vacuum tube and ribbon cables. They seem to look ok. Theta motor seems to be woking. I'm leaning towards the theta encoder going wanky. Is that possible?

Mydata theta problem

Electronics Forum | Thu Oct 01 15:25:09 EDT 2015 | adventurelights

Which encoder did you replace? The one sitting on top of the midas shaft and below the small board or the one attached t the motor next to it? I don't even know if the first one is an encoder.

need 103H7570-7024 stepper motor

Electronics Forum | Tue Aug 11 20:29:51 EDT 2020 | kumarb

Not sure if you are still looking for this motor but received a reply from Elissa (Shenzhen) overnight. Hello this is Samsung CP40 R axis motor J1301632,STEP MOTOR THETA,103H7570-7024 we have original used only price is 86usd/pcs Thank you Elissa

QUAD 4C motor error #5

Electronics Forum | Fri Aug 30 05:34:28 EDT 2013 | bobpan

I would check the following: 1. Make sure the head can move in all axis including z and theta by physically moving each. 2. Check the voltage from the main power supply which is located in the middle of the machine on the top of the main board asse

MYDATA My9 Theta error

Electronics Forum | Thu Nov 15 23:45:53 EST 2012 | jaimebc

robgd3, The Z motor can be purchased separately, however, the theta motor can't. You need to buy the whole midas head. I didn't get as far as dissembling the theta motor casing to get to the theta motor. That was my worse case scenario. We ran thou

MYDATA My9 Theta error

Electronics Forum | Tue Dec 18 21:47:14 EST 2012 | jaimebc

So just to update and close this thread, it was the ZFIB board ( the one mounted on top of the theta motor) that was causing the theta motor to error out) Problem fixed. $ 30 dls or so from MYDATA. Hope this helps some one down the road.

GSM1 occasional fault

Electronics Forum | Tue Jan 26 08:57:01 EST 2010 | Jeff

Check your belt tension on the theta motor.

F-MOT-MSETDYN Theta/12: No axis movement detected by transducer

Electronics Forum | Thu Feb 06 20:23:35 EST 2020 | bilalfarooqi

Hey everyone, We use a MyData MY12 machine and we are experiencing a problem with the Midas head. I recently replaced a torn vacuum tube that goes on the zfib card. The machine worked perfectly for a day and a half but now MY12 has completely stoppe

MYDATA My9 Theta error

Electronics Forum | Tue Nov 20 15:03:37 EST 2012 | jaimebc

Bruce, Since we had spares, I replaced the X wagon cables, XFMB cable, nothing. FFX Cable, nothing. Swapped mot cards, nothing. Vaccum seal, nothing.At this point I truly believe the problem is either on the theta encoder or the theta motor. Unfortu

F-MOT-MSETDYN Theta/12: No axis movement detected by transducer

Electronics Forum | Fri Feb 07 13:17:32 EST 2020 | bk

I am assuming you are initializing each motor individually through the service program. The z motor theta is hard to see so I put a mark on it with a colored marker so you can watch if the midas tool nozzle is actually turning or not. You should be a

  1 2 3 4 5 Next

theta motor searches for Companies, Equipment, Machines, Suppliers & Information

water-based, pH neutral cleaning agent

IPC Certification Training from the comfort of your home or office
PCB AOI

High Precision Fluid Dispensers
Pillarhouse USA for handload Selective Soldering Needs

Nozzles, Feeders, Spare Parts - Siemens, Fuji, Juki, Yamaha, etc...
Inline Cleaning Machine Hydro-clean Array

World Source Equipment: Used equipment sale. Hundreds of items on sale.
ACI Technologies, Inc - One Day Training

"Find out how you can receive priority in SMTnet Search with out Sponsor membership."