Electronics Forum: trolley and pick and up and point (Page 1 of 3)

Simultaneous pick up with 0402 and 0201 components

Electronics Forum | Thu May 05 19:13:33 EDT 2016 | darby

Thanks Sr. If you have zero tolerance for simul pick up in your component files then you will not have simul pick up due to variances in your head offsets. So you are saying that on your Juki you run a tolerance for 0201? All other head positions at

Simultaneous pick up with 0402 and 0201 components

Electronics Forum | Thu May 12 00:18:55 EDT 2016 | darby

Sorry for delay - been flat out. Sr - I understand what you are saying. My concern is that combined with the head offsets and variations in pick points (i.e. having to teach feeder positions for very slight amounts like 0.05mm)then you cycle times wi

Multi-part reeling for pick and place

Electronics Forum | Fri Jul 16 13:41:24 EDT 2004 | Frank

I agree with everybody here. There are plenty of better options than what you have proposed. Without knowing your equipment brand, or what type of offline software you have, if any, I have a few suggestions. 1) If you don't have any offline softwa

Matrix/Jedec tray changeover at pick and place surface mount.

Electronics Forum | Tue Oct 12 13:03:18 EDT 2021 | cunningham

Afternoon all, Do you use any special surface other that ESD matting when changing over matrix trays? We currently use a earthed wire trolley that we keep trays and MSD bags on and when replenishing stock its carried out on the trolley. Does anyon

Neoden and YX chinese pick and place machines, looking for users opinions

Electronics Forum | Wed Feb 24 10:57:52 EST 2021 | spoiltforchoice

And then they make a new machine, and start the software all over again, or change the hardware so much the older model doesn't get any of the software tweaks on the new one even if they are supposedly the same model.... Neoden bigger machines shoul

Dye and Pry

Electronics Forum | Fri Mar 14 11:25:02 EDT 2008 | hegemon

ol' hege has got to agree with Chunks and Dave. Seems every time there is a problem, the finger is first pointed at the process. For my $.02 it doesn't matter if your process is 100% bulletproof, procurement will screw it up by finding a vendor that

BGA rework and inspection

Electronics Forum | Thu May 30 10:31:03 EDT 2002 | robbied

Hi Yannick. This is an issue that we are just recently getting into but here is some ifo that I have gathered so far. I have seen/ used 2 different rework machines. The one we have bought is a 'PACE TF2000' which was at the lower cost end of the mar

Need used pick and place for low volume, high mix - suggestions?

Electronics Forum | Tue Apr 27 23:10:16 EDT 2010 | mbrunton

I am looking at buying a pick and place machine to assemble the circuit boards we make. Most of the boards are small (2 to 10 square inches), most are 2 sided, and have maybe 20-50 parts per side. I use mostly 0805/0603 chips, SOT-23, SOD-123, SOIC

First Off and P+P Data

Electronics Forum | Wed May 25 17:58:07 EDT 2011 | rssimmons

The SimmScope is a first article inspection system that uses an overhead digital microsope on a motorized gantry to inspect the board - much like an AOI - except that it does not automatically make the pass/fail decisions. It is up to the operator to

Fuji Pick and Place Machines

Electronics Forum | Sat May 08 09:59:21 EDT 2004 | fastek

What you need to remember is Fuji didn't make a name for itself by building this XP platform. They're strengths are/were in their chipshooters. Don't just assume that because it's Fuji it won't have reliabilty issues. I'm not sold on this platform ye

  1 2 3 Next

trolley and pick and up and point searches for Companies, Equipment, Machines, Suppliers & Information