Electronics Forum: twist (Page 1 of 22)

warp and twist

Electronics Forum | Mon Feb 13 23:05:02 EST 2017 | swestheimer

I have been asked a very good question but have not been able to find a good answer. IPC for both PCB and PCBA refer to the X & Y dimensions to measure warp and twist but how would you determine the warp and twist for a round PCB or PCBA?

warp and twist

Electronics Forum | Tue Feb 14 22:20:10 EST 2017 | swestheimer

Hi Dave, Thank you for your inputs as they were good suggestions. I however let out one important detail and that this is IMS material and not glass reinforced so I think that there is more bending going on during processing than warping and twistin

warp and twist

Electronics Forum | Tue Feb 14 09:10:43 EST 2017 | davef

Assuming the traces run parallel and perpendicular to each other, I'd choose one direction the traces run as "x" and the other direction for "y." Then I'd pick a unique identifier on the board to insure proper orientation. Next, I'd measure warp and

PCB assembly bow and twist

Electronics Forum | Fri Dec 27 16:26:30 EST 2013 | davef

I expect to find the specification and measurement method for the bow & twist of an assembly to be on the assembly drawing. Comments are: * Expecting that an industry committee to write a bow & twist spec for an assembly they know nothing about is n

PCB assembly bow and twist

Electronics Forum | Thu Dec 26 12:12:55 EST 2013 | igorfo

Dear Friends, I need your help to understand requirements and measurement methods for bow and twist of assembled PCB (PCBA have and SMT and TH components). I already check all posts on the site but didn't found any related to my question answers.

Bow and twist of PCB's

Electronics Forum | Mon Apr 23 11:44:55 EDT 2001 | CAL

650 Standards are also located in the back of IPC JSTD-001. I am currently looking at 4 pages on bow and twist. Percent bow = R1-R2/L x 100 (R1= Highest point; R2=lowest or resting point; l= length) Percent twist=(R1-R2)/(2xL)x 100 Sorry if this is

Bow and twist of PCB's

Electronics Forum | Mon Apr 23 07:56:20 EDT 2001 | dougie

Hi Kris, DISCO!!!! Cheers, Dougie.

Bow and twist of PCB's

Electronics Forum | Mon Apr 23 14:36:16 EDT 2001 | CAL

Ah Yes.............My 600 A version has it in the back as well Cal

Bow and twist of PCB's

Electronics Forum | Fri Apr 20 07:12:22 EDT 2001 | wbu

Dougie, oh yes, it�s a bit short that chapter. I have the Revision e in front of me and this one contains in the appendix the needed IPC-TM-650 Test method for bow and twist. Can�t think that they don�t have that in the new revision. Hope you find

Bow and twist of PCB's

Electronics Forum | Fri Apr 20 07:30:14 EDT 2001 | wbu

In short: the measured deviation / the length this deviation occurs * 100% = % of deviation Actually we encounter mostly "twist" so we put the board on a flat surface, hold it down at the corners to see if any of the corners lifts, measure the heig

  1 2 3 4 5 6 7 8 9 10 Next

twist searches for Companies, Equipment, Machines, Suppliers & Information

Equipment Auction - Eagle Comtronics: Low-Use Electronic Assembly & Machining Facility 2019 Europlacer iineo + Placement Machine  Test & Inspection: Agilent | Tektronix | Mantis Machine Shop: Haas VF3 | Haas SL-20 | Mult. Lathes

World's Best Reflow Oven Customizable for Unique Applications
Selective soldering solutions with Jade soldering machine

High Precision Fluid Dispensers
Selective soldering solutions with Jade soldering machine

High Throughput Reflow Oven