Electronics Forum: use scale on conformal coating (Page 1 of 3)

Bubbles on solder joint(after conformal coating curing)

Electronics Forum | Wed Nov 25 15:16:04 EST 2009 | sforman1

Why in heavens name are you using a heat or air cure conformal coating. Why aren't you using a 100% solids UV cure system. You would never have an issue like this Sam Forman MicroCoat Technologies

Bubbles on solder joint(after conformal coating curing)

Electronics Forum | Fri Dec 18 09:27:51 EST 2009 | sforman1

Tom: Once again - why are you using solvent based conformal coating. 1B31 is OK as a CC but it contains Toluene and MEK!! It is only 35% solids which means you are trying to get rid of 65% solvent. If you must use it due to customers requirement then

Bubbles on solder joint(after conformal coating curing)

Electronics Forum | Sun Nov 29 20:04:05 EST 2009 | prodivegsr

Hi sforman1, The chemical that i'm using is a solvent based coating humiseal 1B73. From my understanding,the UV curing is mainly for UV curable coating like the UV40. And the main advantage of using UV curing is for fast throughput and environment

Bubbles on solder joint(after conformal coating curing)

Electronics Forum | Wed Dec 02 10:14:42 EST 2009 | duso02

As a large coating house we use 1B73 daily and we have very few issues with bubbles. We very rarely bake it as the air cure is so short. Also, we only use thinner 73 vice 521. Another question would be; how is it being applied? How thick are you appl

Bubbles on solder joint(after conformal coating curing)

Electronics Forum | Wed Dec 02 20:11:37 EST 2009 | prodivegsr

Hi Lou, we are using a fluid dispensing machine. our current requirement is around 50um. From the Datasheet,the thinner 73 has a higher evaporation rate of 1.0 comapring with thinner 521 at 0.6... does the higher evaporation rate eliminate the bu

Bubbles on solder joint(after conformal coating curing)

Electronics Forum | Sun Nov 22 19:53:10 EST 2009 | prodrivegsr

Hi Ju Yong, The PCB are dry in an airseal cabinet(Staging Chamber) before IR Oven. The bubbles show at around body and solder joint area. You mean the moisture will create bubbles ? Able to advice the humidity and temperature that you are using in

Bubbles on solder joint(after conformal coating curing)

Electronics Forum | Sun Nov 22 19:59:26 EST 2009 | prodivegsr

Hi Davef, The bubbles occurs at the body also...there's also a washing process before the conformal coating:-the Flux residue are removed after washing. ... The curing profile is also something that we are looking into during the initial troubles

defect on PCB acrylic conformal coating

Electronics Forum | Wed May 08 14:24:22 EDT 2013 | wahahasteven

we are using acrylic conformal coating on the PCB. Under the same program, same parameters (not changing anything on the machine), and we always found one or two boards have some spots which are not coated (shown as picture). The location of the spot

defect on PCB acrylic conformal coating

Electronics Forum | Thu May 09 13:49:24 EDT 2013 | davef

First, it appears that your solder mask and your coating material appear to be incompatible. Second, IPA leaves a residue that's probably not compatible with your coating material, either. IPC-HDBK-830 - Guidelines for Design, Selection and Applic

Bubbles on solder joint(after conformal coating curing)

Electronics Forum | Thu Nov 19 05:18:37 EST 2009 | prodivegsr

Hi All, Recently we are working on the conformal coating process using Humiseal chemical 1B73 and thinner 521. Bubbles on component body/joints are seen after gone through the IR Reflow Oven. During the conformal coating, only tiny bubbles seen af

  1 2 3 Next

use scale on conformal coating searches for Companies, Equipment, Machines, Suppliers & Information

Count On Tools, Inc.
Count On Tools, Inc.

COT specializes in high quality SMT nozzles and consumables for pick and place machines. We provide special engineering design service of custom nozzles for those unique and odd components.

Manufacturer

2481 Hilton Drive
Gainesville, GA USA

Phone: (770) 538-0411

2024 Eptac IPC Certification Training Schedule

Software for SMT placement & AOI - Free Download.
thru hole soldering and selective soldering needs

Training online, at your facility, or at one of our worldwide training centers"
Sell Your Used SMT & Test Equipment

Nozzles, Feeders, Spare Parts - Siemens, Fuji, Juki, Yamaha, etc...
Pillarhouse USA for Selective Soldering Needs

High Throughput Reflow Oven


SMT & PCB Equipment - MPM, DEK, Heller, Europlacer and more...