Electronics Forum: versatronics (Page 1 of 2)

New forum for UK Versatronics & other low-end P&P machine users

Electronics Forum | Fri Aug 27 08:20:22 EDT 2010 | whitewing

I've just set up a small forum for users of the old Versatronics Pick/place machines, but also for discussion of low-end pick/place equipment, with a UK/Europe-based emphasis. URL : http://www.electricstuff.co.uk/forum

Low cost prototyping machines

Electronics Forum | Tue Jun 14 10:58:11 EDT 2005 | Rob

Hi does anyone have any good experiences with low volume, low cost prototpying SMT machines? My experience is mainly with high volume manufacturing so I've never really looked into this market & the manufacturers (except Quadra & Versatronic & I wa

Pick Place Programmer

Electronics Forum | Mon Jun 18 09:52:42 EDT 2018 | robl

Seen a fair few SMT programming houses with modified Quads and Versatronic machines. We had a play at this too, and didn't look too taxing. We have an IC that takes 40 mins to programme, and the programming house runs through the night, gang prog

Low cost prototyping machines

Electronics Forum | Thu Jun 23 05:06:07 EDT 2005 | ajaydoshi

Hi does anyone have any good experiences with low > volume, low cost prototpying SMT machines? > > My > experience is mainly with high volume > manufacturing so I've never really looked into > this market & the manufacturers (except Quadra & >

Low volume prototyping

Electronics Forum | Fri Jul 07 06:55:02 EDT 2006 | Rob

I HATE them. I have tried most types and am not impressed. By the time you add on all of the extras such as tape feeders, trays, nozzles, guidance, etc. you could nearly buy a used Mydata/Contact/Quadra/Versatronics/Quad/Daum which would give you p

Versatronis RV1 frame grabber

Electronics Forum | Fri Feb 13 09:36:58 EST 2009 | jlbelectronics

Hi, I have a Versatronics RV1 pacer with 7 feeders and camera system. The camera function seems to have stopped working. The compostite output from the camera is working anf the cable has beend chekced. The PC frame grabber card is manufactured by A

RV4S capability.

Electronics Forum | Fri Sep 24 17:40:30 EDT 2010 | microman

Hello, We are looking at purchasing a Versatronics RV4S. I am looking for some impartial advice on it's capabilities. The majority of our boards will have 0603 passives and maybe one or two 100 pin TQFP's, however, we are expecting to go down to 040

Training plan for SMT Operator

Electronics Forum | Mon Feb 04 22:29:55 EST 2013 | armandogomez

This is a very common question, I can relate to your question I have here almost the same setup on the smt line, printer a DEK, MY12 and an awful versatronics oven, about the question about the responsibilities, here the operator has only the knowled

Pick and place machine for small productions. Any suggestions?

Electronics Forum | Thu Sep 19 04:21:11 EDT 2013 | spoiltforchoice

The budget is very small, if there is genuinely a saving to be had by moving this work in-house and away from subcontracting you should really be able to justify spending more. If you can't increase the budget maybe try shopping around for more compe

Quad 1000, looking for opinion

Electronics Forum | Wed Nov 02 11:27:45 EST 2005 | rlackey

Depends on the actual requirements of the machine & the skill of the operator, but for that sort of money I've seen Juki 570's with a stack of feeders, Versatronics RV4's, older Mydata's, Samsung CP30's, Essemtec, Philips CSM's etc. I even once bough

  1 2 Next

versatronics searches for Companies, Equipment, Machines, Suppliers & Information

Blackfox IPC Training & Certification

Reflow Soldering 101 Training Course
Voidless Reflow Soldering

Stencil Printing 101 Training Course
SMT feeders

Software for SMT placement & AOI - Free Download.
2024 Eptac IPC Certification Training Schedule

Best Reflow Oven