Electronics Forum: vib feeder (Page 1 of 4)

Mydata vib feeders

Electronics Forum | Thu Mar 24 10:15:56 EST 2005 | blueflag

Dear All We are using a my12 also tp11 with VIB feeders we are having major problems with ics in tubes are there any machines available to convert ics up to so16 from stick to tape & reel and are the cost effective ?????? Thanks Colin

Mydata vib feeders

Electronics Forum | Fri Mar 25 15:13:30 EST 2005 | pdeuel

Also search "Tape and Reel" useing your favorite search engine. We sometimes have an outside vendor tape this stuff for us. They use generic mod tape that dose not fit properly the parts supplied to them that also causes pick problems.

Mydata vib feeders

Electronics Forum | Thu Mar 24 22:39:22 EST 2005 | pmd

My opertaors have lots of setup problems with vib feeders. They dont realize that the chip weight pushes parts down and when feeders run low it's the frequency that drives the parts. Mixing parts with diferant phisical deminsions and masses in the sa

Mydata vib feeders

Electronics Forum | Thu Mar 24 10:20:21 EST 2005 | Rob

Hi Colin, Yes there are such machines available, new prices start at around $10K. You can also have a taping house sort out your current stock & buy in taped for next time which would be far cheaper (However pack quantities will change a lot). If

Mydata vib feeders

Electronics Forum | Thu Mar 24 17:36:31 EST 2005 | Grant

Hi, Yes MYDATA vibration feeders are a nightmare, but you might want to check the feeder. We had one that would vary a lot, and it never seemed to be able to be set to the right vibration level for consistent feeding. It turned out to have a problem

Need info. on vib times for Siplace 80f4 Users

Electronics Forum | Mon Sep 14 12:33:27 EDT 1998 | Justin Medernach

Hello, I have a Siplace 80f4 placement machine. I work in a prototype environment and the majority of my components arrive in stick format. I am having a heck of a time trying to get these vibratory feeders to work. If anyone is using this platfor

Re: Need info. on vib times FROM Siplace 80f4 Users

Electronics Forum | Mon Sep 14 12:35:05 EDT 1998 | Justin

Hello, I have a Siplace 80f4 placement machine. I work in a prototype environment and the majority of my components arrive in stick format. I am having a heck of a time trying to get these vibratory feeders to work. If anyone is using this pla

Re: Need info. on vib times for Siplace 80f4 Users

Electronics Forum | Mon Sep 14 21:40:25 EDT 1998 | Stefan W.

Unfortunatly there are too many variables to play with that you can't make a general rule for the vibration time. However, I suggest you increase the vibration time and lower the vibration force ( AC voltage ). For an SO 8, I would use 600 ms for an

Re: Need info. on vib times for Siplace 80f4 Users

Electronics Forum | Tue Sep 15 14:12:36 EDT 1998 | Justin Medernach

Unfortunatly there are too many variables to play with that you can't make a general rule for the vibration time. However, I suggest you increase the vibration time and lower the vibration force ( AC voltage ). For an SO 8, I would use 600 ms for

QFNs in tubes. What is the best feeder to use for Juki?

Electronics Forum | Thu Jan 12 11:41:02 EST 2012 | babe7362000

We are recieving many QFN's in Tubes instead of trays and tape. Does anyone have luck with these in a tube feeder, or vib plate? We cant justify to order a full reel because the cost of the part.

  1 2 3 4 Next

vib feeder searches for Companies, Equipment, Machines, Suppliers & Information