Electronics Forum: vitronics and nozzle (Page 1 of 17)

vitronics delta 6622 fluxer

Electronics Forum | Thu Mar 18 07:58:43 EDT 2010 | mun4o

It is a pressurized system, and , Yes , there are a message "No flow nozzle 1".Our machine have not 'ShoRate' gauge at the back of the machine.There are only 3 gauge for flow on the front side , like watch ???

vitronics delta 6622 fluxer

Electronics Forum | Wed Mar 17 04:26:44 EDT 2010 | mun4o

Hi, we have vitronics delta 6622 in your production.Problem with fluxer starting 3 weeks ago.Fluxer moving, but not spraing????I check flux system , and dont find any problems with machine.Clean the spray nozzle with compressed air , but nothing.may

vitronics delta 6622 fluxer

Electronics Forum | Wed Mar 17 10:12:16 EDT 2010 | dj_jago

Is it the pressurized system or the pump system you have fitted to the machine? Are you getting an error message 'No flow nozzle 1'? Check the 'ShoRate' gauge at the back of the machine and make sure the ball bearing rises in the glass tube when you

Max and Min nozzle settings on CP7

Electronics Forum | Sat Jul 24 04:02:18 EDT 2004 | kent_peterson

Two ways at it.You could just put the same nozzle for both the min and max.Or you could move the feeder into a location that has similar parts using the nozzle you want. With the feeder setup it should be optimized for the least amount of nozzle ch

Max and Min nozzle settings on CP7

Electronics Forum | Sat Jul 24 04:02:21 EDT 2004 | kent_peterson

Two ways at it.You could just put the same nozzle for both the min and max.Or you could move the feeder into a location that has similar parts using the nozzle you want. With the feeder setup it should be optimized for the least amount of nozzle ch

Max and Min nozzle settings on CP7

Electronics Forum | Mon Aug 02 13:06:10 EDT 2004 | jbabson1

If the CP7 is like the CP643, it defaults to the MAX size unless that nozzle is skipped. Then it would switch to the next smaller nozzle on that head.

Max and Min nozzle settings on CP7

Electronics Forum | Tue Jul 20 04:16:02 EDT 2004 | Charles Huang

Wondering if there any CP7/F4G programmers out there that can help me out with this one. I'm assuming the setting for max and min nozzle in the "environment" section of the part data would allow me to use either the specified max OR min nozzle in th

vitronics delta wave malfunction errors :pcb expected at exit

Electronics Forum | Fri Sep 14 03:43:16 EDT 2012 | mili

Hello!I have a delta wave with these problems:offtime of lambda wave tracking is too long and when modify offtime setting to a negative value for a fast stop on tracking position of lambda wave, the wave pass on stand-by with a delay of half of leg

Coating on solder nozzle for Vitronics selective machine?

Electronics Forum | Tue Aug 16 15:39:07 EDT 2011 | mwest

What type of coating is used on the Vitronics selective solder nozzles? Any help?

Coating on solder nozzle for Vitronics selective machine?

Electronics Forum | Thu Aug 18 10:37:37 EDT 2011 | tombstonesmt

We do not use a Victronics selective solder but we you activ8 102 stainless steel flux from worton metals for our nozzles. Hope this helps.

  1 2 3 4 5 6 7 8 9 10 Next

vitronics and nozzle searches for Companies, Equipment, Machines, Suppliers & Information

Thermal Interface Material Dispensing

World's Best Reflow Oven Customizable for Unique Applications
December 2024 Auction

We offer SMT Nozzles, feeders and spare parts globally. Find out more
Software for SMT

High Precision Fluid Dispensers