## Electronics Forum: volt (Page 1 of 16)

### Resistor Help Needed

Electronics Forum | Thu May 20 09:29:02 EDT 2004 | Dilbert

Three LEDs, 3.5volts @.02amps each is 10.5volts. You said you calculated out an 82 ohm resistor so 82 ohms * .02amps is 1.64volts, I guess your going to use a 12volt supply. P=I*E =.02amps * 1.64volts =.033watts so a .25watt resistor will be fine

### VCD 8 6241 loosing 5 volts supply

Electronics Forum | Mon Jan 25 17:13:53 EST 2010 | bing007

I am working on a vcd 8 with a problem of loosing the 5 volts supply. We have fitted a new supply that also provides the 15 volts. When we remove the connector on the power chassis for the 5 volts the power supply shows OK. When fitted the 5 volts is

### VCD 8 6241 loosing 5 volts supply

Electronics Forum | Mon Feb 01 14:04:12 EST 2010 | bing007

Found the problem. Thanks for the pointers. I had set the voltage to 5.00 volts as it was reading 4.86 volts. I still had the problem. A slghtly burnt wire going into the spade connector on the back of fuse holder 12 (5 volts). The reason the voltage

### Searching for low cost transformer supplier

Electronics Forum | Fri Sep 04 21:04:33 EDT 2015 | sarason

How high a voltage are we talking , 240 volts, 4000 volts , 26000, volts 60,000 volts, 240 volts is easily done as we go up the scale insulation becomes a bigger problem and winding machines have to be much better in control of tension,also at higher

### charging batterys via solar

Electronics Forum | Sat Jan 26 08:44:39 EST 2002 | Bigballs

What would happen if a 2 volt solar cell was hooked through a diode into to a 3.6 volt nicad (3xAA)? would it charge it at all? just a bit but never fully? would battery deliver 3.6 volt after charging? If left long enough would it charge fully?

### charging battery with solar power?

Electronics Forum | Fri Dec 01 23:37:34 EST 2000 | Kel

If i hook a 5amp/12volt solar panel to a 6 volt lead acid battery, would it recharge it? is it as simple as hooking the two together? thanks,

### VCD 8 6241 loosing 5 volts supply

Electronics Forum | Wed Feb 03 18:29:46 EST 2010 | mika

4.85 V - 5.2 Volts. That is on the computer power inlet, Not the on the power supply. /Best Regards

### Question on ANSI/ESD-S20.20-1999

Electronics Forum | Tue May 16 16:32:38 EDT 2000 | Ashok Dhawan

1) I had downloaded ANSI/ESD-S20.20-1999 from www.eosesd.org web site. I am not clear whether section 6.2.3.2 is correct. It states that " All process essential insulators that have electrostatic fields that exceed 2000 volts should be kept at a mi

### MYData issue

Electronics Forum | Tue Jun 19 16:19:34 EDT 2007 | bk

There are no batteries in mydata magazines. This problem means your voltage is outside it's allowed range. In this case I think it's the 15 volts. If you open up the bottom of the machine and pull out the carriage you'll see a rectangular box that ho

### SMD Capasitor

Electronics Forum | Tue Apr 24 02:34:31 EDT 2012 | abyan

Hi..i have o project to make 3A Power supply, and i want to make it using SMD. I want to ask you about SMD capasitor, because i'm a newbie in this type of material.. Actually where could i found SMD capasitor with this specifications: -) 6800uf 35vol

 1 2 3 4 5 6 7 8 9 10 Next

#### volt searches for Companies, Equipment, Machines, Suppliers & Information

Benchtop Fluid Dispenser

World's Best Reflow Oven Customizable for Unique Applications

Find a wide selection of nozzles, solder materials, storage solutions and more at SALESCON