Electronics Forum: volts (Page 1 of 15)

VCD 8 6241 loosing 5 volts supply

Electronics Forum | Mon Jan 25 17:13:53 EST 2010 | bing007

I am working on a vcd 8 with a problem of loosing the 5 volts supply. We have fitted a new supply that also provides the 15 volts. When we remove the connector on the power chassis for the 5 volts the power supply shows OK. When fitted the 5 volts is

VCD 8 6241 loosing 5 volts supply

Electronics Forum | Mon Feb 01 14:04:12 EST 2010 | bing007

Found the problem. Thanks for the pointers. I had set the voltage to 5.00 volts as it was reading 4.86 volts. I still had the problem. A slghtly burnt wire going into the spade connector on the back of fuse holder 12 (5 volts). The reason the voltage

VCD 8 6241 loosing 5 volts supply

Electronics Forum | Wed Feb 03 18:29:46 EST 2010 | mika

4.85 V - 5.2 Volts. That is on the computer power inlet, Not the on the power supply. /Best Regards

VCD 8 6241 loosing 5 volts supply

Electronics Forum | Fri Jan 29 10:53:13 EST 2010 | jeffharley

There are pots on the board in the power supply to adjust the voltages after the machine is powered up. The location of these pots are in the munual supplied with the machine

VCD 8 6241 loosing 5 volts supply

Electronics Forum | Fri Jan 29 12:59:47 EST 2010 | remullis

Something on the 5v side is pulling it down. I would check every thing associated with the harness you are disconnecting. Your shorting somewhere! Don't have a schematic in front of me. Also look for leads getting into the backside of your connecto

Resistor Help Needed

Electronics Forum | Thu May 20 09:29:02 EDT 2004 | Dilbert

Three LEDs, 3.5volts @.02amps each is 10.5volts. You said you calculated out an 82 ohm resistor so 82 ohms * .02amps is 1.64volts, I guess your going to use a 12volt supply. P=I*E =.02amps * 1.64volts =.033watts so a .25watt resistor will be fine

Searching for low cost transformer supplier

Electronics Forum | Fri Sep 04 21:04:33 EDT 2015 | sarason

How high a voltage are we talking , 240 volts, 4000 volts , 26000, volts 60,000 volts, 240 volts is easily done as we go up the scale insulation becomes a bigger problem and winding machines have to be much better in control of tension,also at higher

charging batterys via solar

Electronics Forum | Sat Jan 26 08:44:39 EST 2002 | Bigballs

What would happen if a 2 volt solar cell was hooked through a diode into to a 3.6 volt nicad (3xAA)? would it charge it at all? just a bit but never fully? would battery deliver 3.6 volt after charging? If left long enough would it charge fully?

charging battery with solar power?

Electronics Forum | Fri Dec 01 23:37:34 EST 2000 | Kel

If i hook a 5amp/12volt solar panel to a 6 volt lead acid battery, would it recharge it? is it as simple as hooking the two together? thanks,

Question on ANSI/ESD-S20.20-1999

Electronics Forum | Tue May 16 16:32:38 EDT 2000 | Ashok Dhawan

1) I had downloaded ANSI/ESD-S20.20-1999 from www.eosesd.org web site. I am not clear whether section is correct. It states that " All process essential insulators that have electrostatic fields that exceed 2000 volts should be kept at a mi

  1 2 3 4 5 6 7 8 9 10 Next

volts searches for Companies, Equipment, Machines, Suppliers & Information

PCB Handling with CE

High Speed Precision In-Line SPI System - Mirtec MS-11
Global manufacturing solutions provider

IPC Certification Training from the comfort of your home or office
FPC* - Fluid Pressure Control - Dispensing Pump

We offer SMT Nozzles, feeders and spare parts globally. Find out more
Large PCB Dispensing System

Training online, at your facility, or at one of our worldwide training centers"