Electronics Forum: wave and component and mov (Page 1 of 8)

Heat guns and component damage

Electronics Forum | Tue Jan 31 15:51:04 EST 2006 | russ

Relays huh? I can tell you from previous experience that relays are not a good heat gun candidate. Did you check how long this part can withstand the 240? I do not know what the 4 setting is on a liester but it is probably well in excess of the 24

Heat guns and component damage

Electronics Forum | Tue Jan 31 15:40:44 EST 2006 | mgdrouin1

Comp is relay. I've pulled the spec. Max 240. Using Leister h/g with manual temp settings from 1-6 (20 - 600C)set by the operator. Gun was set to setting 4. They are using the heat gun to reflow the solder after SMT but before wave. High fai

Heat guns and component damage

Electronics Forum | Wed Feb 01 08:12:04 EST 2006 | Chunks

OK, this is easy. You say HIGH fall out, so I can assume 25 or 50%? If so, run 10 without the heat gun and 10 with. This should show you if the heat gun process is the cause or not. If the relay is a surface mount, hand solder them on. If it's a

Solder beads and wave soldering

Electronics Forum | Mon Jul 03 05:39:05 EDT 2006 | ronalds

Hi, I am experience problems while testing wave soldering SMT components that are glued on the solderside (lead free). Between de leads of SOx type IC's and SOT's develop a great deal of solder beads. I have been using a RSS temp.profile while spr

Solder beads and wave soldering

Electronics Forum | Thu Jul 06 12:52:35 EDT 2006 | samir

..and he can put the flux in and keep it a secret too from his customer.. RSS profile on wave?? I never heard of a soak zone for wave preheat...you may be burning off your activator..hence, the beads. For wave preheat, your main goal is to ramp up

wave soldering and solder bridge

Electronics Forum | Mon Dec 17 12:06:58 EST 2007 | pjc

5 Steps to Eliminate Bridges: 1. Establish (wave) Parallelism First and foremost, you must establish board-to-wave parallelism. This is the prerequisite to any wave solder process control. For an understanding of the power of this approach go to ht

wave soldering and solder bridge

Electronics Forum | Mon Dec 17 11:55:08 EST 2007 | chef

I recently had the same problems, solder bridges on every thing I made, different customers boards, etc. I wave with no-clean flux. As I sorted out problems (pin holes, blow holes, splatter, etc.) I found a lot of variable factors. I changed flux,

Clearance between Through hole and chip component

Electronics Forum | Tue Feb 27 20:53:10 EST 2007 | davef

We'll guarantee the two pads are too close together. The proper spacing depends on the orientation of the parts to the wave. * Do the pads hit the wave at the same time? * Does one pad hit the wave before the other? If so, which? * How does the 06

Clearance between Through hole and chip component

Electronics Forum | Wed Feb 28 11:43:20 EST 2007 | realchunks

Marcin, Think outside the box. If you are glueing the SMT part down, why not have an aperture cut in your stencil (or recut a stencil) between the SMT part and thru-hole. Wave solder hates SMT glue. This will get rid of your solder short problem

Clearance between Through hole and chip component

Electronics Forum | Tue Feb 27 11:03:09 EST 2007 | Marcin

Hi All, Anybody knows what is the minimum clearance between through hole component and chip component? Problem description: On bottom side of my pcb are only 0603 chip components mounted on glue. One of the component is located very close to hole

  1 2 3 4 5 6 7 8 Next

wave and component and mov searches for Companies, Equipment, Machines, Suppliers & Information

MSD Dry Cabinets

High Precision Fluid Dispensers
Industry 4.0 Reflow Oven

High Throughput Reflow Oven
FPC* - Fluid Pressure Control - Dispensing Pump

High Speed Precision In-Line SPI System - Mirtec MS-11
Large PCB Dispensing System

Outstanding liquid dispensing and UV curing, all within one platform, watch the video.
MSD Dry Cabinets

Software for SMT placement & AOI - Free Download.
ACI Technologies, Inc - One Day Training

Thermal Transfer Materials.