Order by: Relevancy | Date
May 18, 2017 | We are soldering wire 26AWG to jack socket. However after went through washing, baking, coating, cur
Dec 16, 2016 | > Hi all, > > Recently, we are trying to do > wire bonding between a 75 * 75 u
Dec 14, 2016 | As I understand, you are wire bond gold wire to gold pad, where the substrate has good bond strength
Dec 14, 2016 | Hi all, Recently, we are trying to do wire bonding between a 75 * 75 um pad on a chip and su
Jun 28, 2013 | I don't see any requirement for a ferrule on the wire. As long as your insulation clearance is twic
Jun 3, 2013 | Hi, I have a design were power supply multi strand wire (AWG18) are soldered directly on the pcb
Oct 26, 2012 | Hello, I need to find a wire tinning pot with temp control that will conform to J-STD-001 require
Dec 9, 2011 | Using common wire size and through hole diameter, we'd expect that the wave solder process would com
Jan 29, 2010 | hi peter, i have experience with manual soldering iron using automated wire feed,please email to me
Jan 14, 2010 | JBC Tools has a wire solder feed solder iron. You can control how much is dispensed to the tip. I
Sep 10, 2009 | Solder wire is so cheap that unless you have tons of expired spools just throw it away and buy new.
Sep 1, 2009 | We started to use wire from Metallic Resources because they have no expiration date for "properly st
Aug 26, 2009 |
Aug 26, 2009 | Many solder wire suppliers put a on rolls of solder wire either a: * "Date of manufacture" stamp an
Aug 26, 2009 | Hi We have recently noticed that our lead free solder wire is being supplied with expiry dates (t
Mar 18, 2008 |
Mar 11, 2008 | While it's possible, we don't think that soldering a wire of this low of an AWG to a board is a good
Mar 11, 2008 | I agree that wave soldering is probably your best method. Of course if you can, tin the wires in a
Mar 4, 2008 |
Feb 28, 2008 |
Feb 28, 2008 | In the design stages, we have been asked about the difficulty in soldering a 4AWG (stranded) wire to
Aug 31, 2007 | With this length, I would use solid bare wire, solder one end, sleeve with approved shrink tube, sol
Aug 28, 2007 |
Aug 28, 2007 | Sorry...make that .750 long wires, with .125 strips. My mechanical mind was working, but the fing
Aug 27, 2007 | I must be missing something? If you strip 1/8" off both ends of a 1/4" long wire you would have noth
Aug 27, 2007 |
Dec 27, 2006 |
Jul 24, 2006 |
Jul 21, 2006 | Not to argue, but you can use a spot welder to fuse thermocouple wires, also.
Jul 21, 2006 | you can use a thermocouple welder to fuse the wires back. as a matter of fact we use the welder to c
Jul 21, 2006 | How do you plan on fusing the wires back together ?
Jul 20, 2006 | when I order a thermocouple wire for doing oven profiles, it comes in a standard length of 36 inches
Jun 21, 2006 | You may want to pre tin wires then dip into flux before soldering Does work!
Jun 21, 2006 |
Jun 20, 2006 | I was afraid so. Hand soldering wires in general is not difficult, but with your constraint of the
Jun 20, 2006 | It's hand solder, the wires are free issued, what i'm finding is that if we keep the heat and push e
Jun 20, 2006 |
Jun 20, 2006 |
Jun 19, 2006 |
Jun 19, 2006 | Try to dip that wire with flux before insert to PCB. IT's will come better .
Jun 19, 2006 |
Jan 22, 2006 | Wire bonding is a die connect methodology that runs either gold or aluminum wires between pads on th
Jan 21, 2006 | What is wire bonding? What are the applications?