Electronics Forum: yamaha yg200 pick up nozzle (mg2) (Page 1 of 2)

Pick & place nozzle for data switch

Electronics Forum | Mon May 25 21:27:07 EDT 2009 | paligora

Our machine is YAMAHA YVL88II and the issues we have with these data switches are either not being picked up from the feeder at all or are being ped before assembly.

Flason SMT Products

Electronics Forum | Thu Oct 04 00:28:12 EDT 2018 | gaintstar

flason SMT yamaha pick and place machine: http://www.flason-smt.com/product/Yamaha-YG200-Pick-and-Place-Machine.html http://www.flason-smt.com/product/Yamaha-YG200-SMT-Nozzle-209-kv8-m71n9-a0.html http://www.flason-smt.com/product/Yamaha-YG300-311A-

Pick & Place cycle

Electronics Forum | Tue Nov 08 01:46:43 EST 2016 | sarason

Some machines use air blowing to not only place the part but to also help guarantee that when the nozzle is sucking it doesn't end up with a net accumulation of solder paste inside the nozzle. Juki and Yamaha spring to mind. sarason

asymmetrical element in Yamaha VIOS

Electronics Forum | Mon Jun 29 20:59:37 EDT 2020 | kumarb

Hi. The PCB does not look to be heavy. Suggest you try to email their staff - they are very good. Personally have worked with Scott there and he knows the VIOS software very well. https://trans-tec-america.com/contact/ We have the Assembleon Eme

JUKI vs UIC Pick N Place Machines

Electronics Forum | Fri Apr 06 02:17:15 EDT 2018 | rob

@ Sr.Tech, Most of our Chinese spares are Juki & Yamaha original & still bagged, just much cheaper. They wouldn't sell machines in China if all the spares and consumables were at European mark ups. Nozzle wise the Juki 750 & 760 copies are not 100%

Flying Diode

Electronics Forum | Tue Jun 07 00:21:42 EDT 2011 | jacki

Hi All Currently, we encountered that the schottky barrier diode was up side down or misalignment during SMT process.And, many parts were blown away as pick up error. What we found is its package space is a little bigger for parts to move. I seek y

Replacement valves for Emerald x / YV88X

Electronics Forum | Tue May 18 09:58:17 EDT 2021 | kumarb

Thank you so much for the advice. We were suspecting blockage but know that we have clean nozzles. Did the air blow out and removed a spot of black matter - perhaps what was an old o-ring? Nozzles are 61 and 62 posing the issue. Our tech said that 64

Machine good/bad points

Electronics Forum | Mon Mar 25 09:26:16 EST 2002 | stefwitt

you should also look into the different placement methods and their advantages and weaknesses. A chip shooter with a rotary head and lets say 18 nozzles always places one component and picks one at the same time. PC board and feeder table move while

Pick & Place Machine Life Cycle

Electronics Forum | Tue Oct 30 03:02:03 EDT 2018 | robl

No issues with the OS, it is called VIOS. Good spares support from China, also should be good USA support as there are a fair few machines there. Assembleon has a website for USA spares, including a lot of the old Yamaha machines. Personally, I

Yamaha/Philips Model Number Cross References

Electronics Forum | Thu Jul 07 19:39:18 EDT 2005 | darby

This is a very difficult question to answer as it will depend greatly on your component mix. I will presume that the CSM 84VZ is of the following configuration: 2 x RDC Synchro Heads. Heads 1 & 2. These are mechanically centering heads with a chucki

  1 2 Next

yamaha yg200 pick up nozzle (mg2) searches for Companies, Equipment, Machines, Suppliers & Information