Electronics Forum: yestech ytv 2050 (Page 1 of 4)

Yestech YTV-2050 AOI

Electronics Forum | Mon May 03 09:54:16 EDT 2004 | smtpro

I had a few questions if anyone is using this machine. We will have one in soon to try out. Does the machine pick up defects well or does it give a lot of false failures and pass up actual defects? How difficult is it to setup a reliable program? Tha

YesTech doubling lens installation

Electronics Forum | Fri Sep 30 12:16:28 EDT 2011 | tomattek

Our company would like to be able to inspect 0201 parts using our YesTech YTV 2050. To do this, we have purchased a doubling lens from YesTech that attaches to our top camera. The problem is, we bought our YesTech used from another CM, not from Yes

Yestech YTV-2050 AOI

Electronics Forum | Mon May 03 16:29:17 EDT 2004 | Craig Miller

Its a good machine. I think it is the best thing out there for the money. You will get false fails with any machine. You should not get false accepts unless you open the tolerances to far. Once you get used to it you can generate a program in few hou

AOI: Comparisons

Electronics Forum | Mon Aug 30 11:52:05 EDT 2004 | JohnR

Rob, I'm also in the evaluation stage. I've seen demos of the MVP ultra, Landrex Optima, VI-1000 (vi-technology), and the YesTech YTV-2050. I've also researched about eight others as well. Including Agilent, Orbotech, Omron, Cyberoptics, Viscom, GSI

AOI side cameras

Electronics Forum | Fri Sep 07 17:38:23 EDT 2007 | bentigano

Hello James. I've got a YesTech YTV-2050 system at work with one top-down camera, and 1 side-view camera for each of the four sides. I do have the side view cameras being used for automated side inspection. There are some parts with markings that are

AOI: Agilent vs. Omron vs. MIRTec/YESTech?

Electronics Forum | Sat Dec 09 12:27:16 EST 2006 | bentigano

The company that I work for is a high-mix, mid-high volume manufacturer, and we also chose the YesTech AOI equipment. We currently have a YTV-2050 (the conveyorized machine with 5 cameras), and also the YTV-1000 (table-top version of the YTV-2050, wi

Yield on 0402 SMT Printed Circuit Board Assemblies

Electronics Forum | Thu Jan 04 20:31:21 EST 2007 | Ben_T

Have you thought about an AOI system? With the system we have where I work, I'm able to run queries that'll tell me DPMO, yield, and pass/fail rates on a board level, part level, and opportunity level. Furthermore, this data can be broken down to see

YesTech YTV-1000 AOI issues

Electronics Forum | Thu Aug 02 10:48:29 EDT 2018 | dleeper

I'm going off fuzzy memories for a YTV-2000 but its probably not too different for the 1000... The motor drivers need to be configured for the specific axis they are driving. This should have been done by Yestech before they shipped them to you. If

YesTech YTV-1000 AOI issues

Electronics Forum | Thu Aug 02 15:06:03 EDT 2018 | jeffallen662

They where bought directly from YesTech and were guaranteed to be programmed from YesTech.

Calibration-YTV-BX

Electronics Forum | Mon Nov 12 15:28:28 EST 2012 | rway

YesTech recommends to calibrate every 6 months. So yes, annually at the least.

  1 2 3 4 Next

yestech ytv 2050 searches for Companies, Equipment, Machines, Suppliers & Information