Electronics Forum: zevatech e9001 error (Page 1 of 2)

zevatech 730 help

Electronics Forum | Thu Mar 02 23:09:20 EST 2006 | kmp

If you have a servo or encoder problem you should be getting alot of errors. Are all feet leveled on a stable floor? It wouldn't take much to shake them. A full coke machine weighs more.

zevatech 570 Driver Error KNOCK position E7018

Electronics Forum | Thu Mar 30 08:04:56 EDT 2023 | hub

Hello, I'm looking for zevatech (juki) 570 owner that could help me to resolve my problem. I had the following error that occure just before (or sometime a few after) homing the machine : "E7018:Driver Error KNOCK position error ". Previsously I had

Zevatech FS730 error

Electronics Forum | Fri Jan 19 07:21:07 EST 2007 | meritajs

Thank all for your advices. But we had sistem error,which was connected,how we could undestand with failure main PC controller boards.We had swoped winchester memory block and Zevatech operation was restored Best regards Peter

Zevatech FS730 error

Electronics Forum | Thu Jan 11 05:58:35 EST 2007 | Peter

Hi All, We again have problem with Zevatech FS-730 This machine shows error E202162: "System error: T axis of center head: Parameter error when T axis performs PTP action.(Kind of unit)" and it stop running. It does not pick up components. At low spe

Zevatech FS730 error

Electronics Forum | Tue Jan 16 02:31:19 EST 2007 | meritajs

The problem is that if we disable center head and even turn off the cable of center head encoder, it's not helps. The same error appears. And it's all the same it shows error of the center head.

Zevatech FS730 error

Electronics Forum | Sun Jan 14 00:43:28 EST 2007 | jouni

Hi , Please check encoder cable condition of T-motor. Some times works & some time not , sure cable must have some bad contact.

Zevatech FS730 error

Electronics Forum | Thu Jan 18 07:32:12 EST 2007 | Peter, Belgium

Check wether all mass cables are still attached! Especially the ones on the heads are nescessairy. A broken cable is not allways visible. We replaced those mass cables and our problem was solved.

Zevatech or Juki 720 Pick and Place

Electronics Forum | Wed Nov 03 16:16:32 EDT 2010 | briansmi1116

I have a Zevatech 720 that was working great until one day a "E9001 the emergency stop button has been pressed..." error popped up when I turned the machine on. We traced out the circuit and found out what board it went to. I found a replacement an

Zevatech FS730 problem

Electronics Forum | Wed Mar 22 03:00:09 EST 2006 | meritajs

Hi All, We have problem with Zevatech FS-730 This machine shows error E202062: "System error: T axis of head: Parameter error when T axis performs PTP action.(Kind of unit)" and it stop running. It does not pick up components. At low speed it works s

ERROR Message E7216 w/Zevatech FM720..... Need help

Electronics Forum | Wed Jun 29 13:57:26 EDT 2005 | brath

During BOC Align, this error message came up "E7216" Vision System Transmission This problem came up before about a month ago, and now it came back.... Appreciate anyones feedback back on how to rectify this problem..... Thanks Ab

  1 2 Next

zevatech e9001 error searches for Companies, Equipment, Machines, Suppliers & Information

Selective soldering solutions with Jade soldering machine

High Precision Fluid Dispensers
Selective Soldering Nozzles

High Throughput Reflow Oven
Equipment Auction - Eagle Comtronics: Low-Use Electronic Assembly & Machining Facility 2019 Europlacer iineo + Placement Machine  Test & Inspection: Agilent | Tektronix | Mantis Machine Shop: Haas VF3 | Haas SL-20 | Mult. Lathes

World's Best Reflow Oven Customizable for Unique Applications