SMT BGA voids Formation and prevention


November 13, 2018


Joy Rong


Address: 10 Building, Huaide Cuihai Industrial Park, Fuyong Street, Bao'an, Shenzhen, China Tel: +8618779975930 E-mail: Written by Joy Rong More details: SMT BGA voids Formation and prevention News: The 2nd China Manufacturing Technology-Automation Exhibition (CMM) & the 1st China Electronics Manufacturing Resource Exhibition (CEM) was held at the Dongguan International Convention and Exhibition, such as B&P, Anda, Huancheng, Deshen Huawei, OPPO, VIVO, Xiaomi, ZTE, Foxconn, Flextronics, Lenovo and so on, More than 500 electronic manufacturing companies participated in the exhibition. In the annual feast of the field, the realization of mobile phone production automation can reduce 60% of employees? BGA voids cause current-intensive effects and reduce the mechanical strength of the solder joint. Therefore, from the perspective of reliability, the cavity should be reduced. So how can you reduce BGA voids? There are many reasons for the formation of BGA voids, such as the crystal structure of the solder joint alloy, the design of the PCB, the deposition amount of the solder paste, the reflow soldering process used, and the voids in the soldering process. Next, we will explain the formation and prevention of BGA solder joint voids from the layer of solder paste to reduce the number of BGA solder joint void formation. 1.Furnace temperature curve is improperly set ① In the temperature rising section, the gradient is set too high, causing the rapidly escaping gas to detach the BGA from the pad; ② The duration of the heating section is not long enough. When the temperature rises, the gas that should be volatilized has not completely escaped. This part of the gas continues to escape during the reflow phase, affecting the fluxing system to play a role in the reflow phase. 2. The solder paste solvent is not properly matched ① During the heating phase, the rapidly escaping gas propels up the BGA, causing misalignment and barriers; ② During the reflow phase, a considerable amount of gas still escapes from the solder paste system, but is limited by the narrow space between the BGA and the pad. These volatile gases cannot smoothly escape through this space, causing them to be squeezed. Molten solder joints. 3. Insufficient ability of solder paste to wet the pad 4. The surface tension of the solder paste system is too high during the reflow phase 5. The solder paste system has a high non-volatile content 6. Carrier rosin quality 7. The amount of rosin used Another reason for the BGA cavity is the back-wetting phenomenon during the welding process. The formation of this phenomenon is related to the duration of action of the active material in the solder paste system and the duration of action. During the BGA reflow soldering process, BGA pads are more prone to this undesirable phenomenon than SMT solder paste soldering. After realizing these influencing factors, the corresponding testing measures were added in the research and development. For example, we introduced a thermogravimetric analyzer to conduct thermal analysis on the materials to be used and the solder paste produced, to visually understand these thermal characteristics, and to test Differences between design assumptions and actual performance, measures are taken to overcome them to ultimately meet the process requirements; and surface tension measurements are performed. The appropriate surface tension range is finally determined by measuring the surface tension of the solder paste system and its affected objects at different temperatures. Family of Industrial X-ray inspection machine & BGA rework station Last Article: SMT BGA solder ball inspection method Next Article: Detecting advantages of AOI and X-ray Inspection Equipment Maybe you still are interested in: Importance of X-ray inspection technology in the SMT FAI/ First Article Inspection Highest Quality levels Tool X-ray for industries-SMT/batteries/ceramic/Electronic /semiconductor; The difference between the detection equipment AOI & X-RAY ...

  • Download SMT BGA voids Formation and prevention article
  • To read this article you need to have Adobe PDF installed

You must be a registered user to talk back to us.

Company Information:

Seamark zm Tech Group

Seamark ZM PCB BGA X-ray Inspection system Equipment -14 years experience in SMT field, Our experience will provide good solutions. X-Ray Inspection, BGA reworks tation,Full auto X ray SMD component machine

Shenzhen, China, China


  • Phone +8618779975930

Seamark zm Tech Group website

Company Postings:

(6) products in the catalog

(3) technical library articles

  • Apr 27, 2018 - Understanding the Heat Output of your BGA Rework Station | Precision PCB Services, Inc
  • Apr 27, 2018 - Hot Air vs. IR BGA Rework Stations | Precision PCB Services, Inc
  • Feb 22, 2018 - Hand Soldering with Lead Free Alloys | Metcal
  • Dec 07, 2017 - Utility of Dual Applicators for Non-Atomized Conformal Coating to Improve High-Volume Manufacturing Optimization | Nordson ASYMTEK
  • Nov 08, 2017 - Void Reduction in Reflow Soldering Processes by Sweep Stimulation of PCB Substrate | kurtz ersa Corporation
  • Browse Technical Library »

SMT BGA voids Formation and prevention article has been viewed 114 times

guided rework station ersa

 Reflow System