SMT, PCB Electronics Industry News
  • SMTnet
  • »
  • Industry News
  • »
  • Plan your engineering process improvement with a monthly online webinar

Plan your engineering process improvement with a monthly online webinar

Apr 13, 2017

Process support when and where you need it!

Process support when and where you need it!

Solderability Benchmarking, Failures & Testing Methods
14th August

All our webinars are based on 2.30pm UK time go to https://www.bobwillis.co.uk/events/

Benchmarking you PCB surface finish or the impact of baking boards or components can be simple in production and the laboratoy. Long term solderability of component terminations and printed circuit boards is fundamental in modern assembly processes. This is all practical experience not just theory for the presenters countless studies in industry. Understanding how to conduct simple shop floor assessment of components or using laboratory test methods will be discussed along with artificially age coatings to simulate their useful life. Solderability can impact yield and reliability and making sure engineers understand the test methods onsite, or when subcontracting you’re testing to a laboratory, is key to ascertaining the correct root cause of your process problem.

The webinar will last approximately 60-90mins including a question and answer session for your process problems. If you have a specific process problems with reflow send it to Bob to include in the webinar

Presented by Bob Willis

Topics covered:
 
Test specifications
Test methods
Selecting the best procedure
Ageing samples
Assessment of results
Solderability failures

The webinar material includes slides from the event, solderability testing wall charts and design files for solderability test board to use in your factory


PCB Outgassing and How to Test Bare or Assembled Boards
11th September

All our webinars are based on 2.30pm UK time go to https://www.bobwillis.co.uk/events/

Printed circuit boards outgas during soldering causing solder voids, solder balls and other process problems. Outgassing can occur in wave, selective and reflow soldering and it’s important first to non-destructively test samples to find the root cause. It’s possible to test bare or assembled boards to examine the potential for failure and eliminate some of the popular misconception in industry. There some different methods which can easily be conducted in manufacture before proceeding to costly laboratory analysis and we show you how to do it and the typical results you can find!!

The webinar will last approximately 60-90mins including question and answer session

Presented by Bob Willis
 
Topics covered:

Type of outgassing from vias, through holes and solder masks
How to Test samples in manufacture
Test method procedures
Type of defects and how they can appear with tin/lead and lead-free alloys
Void formation in wave selective and PIHR joints
Correct specification of your boards

A copy of the slides presented during the webinar are provided at the end of the event along with a written procedure for testing


Solder Shorts & How to Eliminate Them – In Selective & Wave Soldering
17th October

Solder short and unsoldered joints are fundamental defects in manufacture and can occur due to design, process change, change in materials or poor process set-up. Some fundamental choices in the methods of assembly and soldering process will increase solder shorts and this session will look at the causes and cures of the solder short

During the session, your presenter will show many causes of solder shorts forming and different solutions to the problem, both process and design tricks of the trade. Process tricks are particularly useful to the contract assembler finding it difficult to get design changes pasted customers. However, many changes in design are very simple, quick and will have no impact on function, reliability or product operation. Some suggestion allows for greater design density and reduce the possibility of product failure

Presented by Bob Willis who spent many years running the Electrovert Wave Soldering Master Class, both one and two-day theory and hands on training in Europe. Bob still runs his own courses on selective and wave soldering for customers worldwide

Each webinar last approximately 60-90 mins with the opportunity for questions on you process issues. Registered delegates on the webinar can send their own problem images for discussion during the webinar

Topics covered include:

Selective & wave soldering process
Flux activity & De-Activation
Solder drainage & cooling rates
Wetting speed
Design & layout
Solder shorts
Solder flags
Solder whisker
Impact of solder pallet design
Process optimisation

A copy of the slides presented during the webinar are provided at the end of the event


Ball Grid Array, Bottom Mounted Component Design, Assembly, Inspection & Defect Elimination
13th November

This webinar includes all BGA (Ball Grid Array), BMC (Bottom Mounted Components), PoP (Package On Package) component assembly and process setup with inspection methods and common failure detection and elimination. Bob produced the first training videos, interactive CDs on area array technology and the first book on PoP assembly and soldering

Bob’s session features many unique process video clips on testing and failures and make his sessions come alive providing a much better understanding of the root cause of failure and corrective action. A FREE copy of Bob’s Ebook on PoP is available to delegates and a copy of his area array posters is provided to each engineer attending this course

If you have a specific process problems with reflow send it to Bob to include in the webinar

Topics will include:

Package types
Design and PCB guide lines for parts
Assembly process options
Inspection standards
Common process and reliability failures
Defect Investigation techniques and corrective action

A copy of the slides presented during the webinar are provided at the end of the event plus a link to a text book on PoP assembly and inspection wall charts for QFN inspection

Nov 20, 2018 -

NPL New 2019 Webinars are Launched

Oct 23, 2018 -

Soldering & Assembly Webinars for 2019 Anounced

Aug 23, 2018 -

Manual Cleaning A Step by Step Guide Online

Aug 23, 2018 -

Cleaning, Contamination Testing & Defects Photo Album

Jul 03, 2018 -

Solder Squeeze Out on Underfilled Boards - Defect of the Month

Jul 03, 2018 -

New Book Reviews from Bob Willis June2018

Mar 25, 2018 -

Soldering, Coating, Cleaning and PCB Process Failures from the Desk of Bob Willis

Mar 24, 2018 -

Dendrite Failure – Causes & Cures Webinar

Oct 23, 2017 -

Manual Cleaning of Printed Board Assemblies – Step By Step Guide Coming Soon

Oct 23, 2017 -

New Online Webinars from the Desk of Bob Willis

79 more news from ASKbobwillis.com »

Jan 17, 2019 -

Speedprint to Demonstrate Small to Large at APEX 2019.

Jan 17, 2019 -

MIRTEC Appoints Kirby & Demarest in the Pacific Northwest

Jan 17, 2019 -

IPC Issues Call for Participation for IPC E-TEXTILES 2019

Jan 17, 2019 -

KIC and iTAC Software AG Integrate Smart Reflow Process Data in the MES i4.0 Solution

Jan 17, 2019 -

Hover-Davis announces its 30 Year anniversary, new feeder and material automation solutions on display at IPC Apex Expo

Jan 17, 2019 -

Z-AXIS upgrades, expands robotic conformal coating at SMT contract manufacturing center near Rochester, NY

Jan 17, 2019 -

What is the electrical conductivity of an N-type semiconductor?

Jan 17, 2019 -

Why is there a sound when some appliances are plugged in?

Jan 17, 2019 -

If I was suspended from a helicopter with the rope, would I get electrocuted if I touched high tension power lines?

Jan 16, 2019 -

ZESTRON to Release ZESTRON® EYE Mobile at IPC APEX 2019

See electronics manufacturing industry news »

Plan your engineering process improvement with a monthly online webinar news release has been viewed 142 times

  • SMTnet
  • »
  • Industry News
  • »
  • Plan your engineering process improvement with a monthly online webinar
x-ray inspection

Six Sigma Training