LED reflow oven for 3W high power LED E10 Main product: Reflow oven with 10 zones, hot air reflow oven, SMT equipment, PCB Assembly Equipment, PCB Assembly Equipment, SMD/SMT Assembly, SMT assembly line, automatic production line Heating System &
New Equipment | Rework & Repair Equipment
The FR-810 Hot Air Rework Station sets a new bar for convective rework. The new, compact and lightweight design (only 2.9 lb.) features a quiet, self-contained turbine air supply, capable of delivering approximately 100 L/min (free flowing). The new
Electronics Forum | Sat Mar 30 03:34:44 EDT 2019 | jacoblemaster
Are you still facing this issue? Well, I am so late to get to know this. I think you first check your evaporator coil if your air conditioner is still freezing up. It has been seen that a dirty airflow coil stops the proper flow of air through it. It
Electronics Forum | Wed Aug 15 11:07:12 EDT 2012 | dwelch123
those can be tricky. Try adjusting the start,stop nuts on the top of the pump. It may not be traveling far enough. Chipbonder your using should be fine and as long as your sure EVERYTHING is clean, using ream wire and solution syringe is being run th
Used SMT Equipment | Soldering - Reflow
Heating zones: 5 Cooling zones: 2 Total heating length: 66 in. Total cooling length: 26 in. Total process length: 127 in. Total on /off load length: 11 in. Overall system length: 138.5 in. Overall system width: 52 in. Overall system height: 5
Used SMT Equipment | Pick and Place/Feeders
Board Size(LxWxT)mm Max.460 x 410 x 2.0㎜,Min.50 x 50 x 0.5㎜ Conveyor flow/speed 좌 → 우 420㎜/sec(with soft-stop) Tact Time 0.16sec/chip,0.38sec/TSOP(32pin) Up ward Vision :0.75sec/QFP(100pin) Repeat ability ±0.06㎜(chip),±0.035㎜(IC)
Industry News | 2017-01-31 03:13:13.0
• JBC improves its Hot Air stations for a better rework process. • The company will be demonstrating the JTSE and TESE stations at the IPC APEX EXPO 2017 • Booth 715
Industry News | 2021-05-21 03:24:27.0
When putting up an HVAC system, it usually requires a precise amount of constant flow for it to properly size piping, pumps, and other necessary accessories. IF the flow control valves are placed improperly, there will be fluctuations in the pressure systems. Thus, to avoid this from happening, a suitable valve should be installed.
_1.jpg)
Parts & Supplies | Pick and Place/Feeders
JUKI 40084405 2070 2080 EJECTOR 2070 SPARE SET Other juki parts: 40083482 SOLENOID VALVE CABLE ASM 40083596 SOLID STATE DRIVE 40083697 HMS_GUARD 40083759 FLOW SENSOR ASM 40084353 AIR CYLINDER 40084395 MAINTENANCE CYLINDER ASM 40084404 HMS GUA
_1.JPG)
Parts & Supplies | Pick and Place/Feeders
JUKI FX3 CPU board 40107372 Other juki parts: 40083482 SOLENOID VALVE CABLE ASM 40083596 SOLID STATE DRIVE 40083697 HMS_GUARD 40083759 FLOW SENSOR ASM 40084353 AIR CYLINDER 40084395 MAINTENANCE CYLINDER ASM 40084404 HMS GUARD EXCHANGE ASM(F
Technical Library | 2019-11-20 22:44:25.0
Salt spray test chamber is used to test teh salt corrosion resistance ability of hardware, metal and other auto parts,the chamber can quickly detect the corrosion resistance degree of products in the temperature, humidity and salt spraying environment, which can effectively improve production efficiency. So what is the reason why such a salt spray test chamber does not spray? As per our past maintenance experience,there are below reasons,customers can have a look,hope it is helpful: 1, the spray tower is blocked; 2, water pipes clogged, water flow can not go in; 3, the air compressor stops running,pls open the air compressor button; 4, main switch of the air compressor outlet is not turned on,pls turn on. 5, the solenoid valve fails, the pressure meter is broken or the pressure is too low, pls check with Climatest and repair it. 6, when the nozzle is clogged, the nozzle should be carefully removed and cleaned,because it is fragile. 7, if the spray pressure is normal, the position of the nozzle glass is also correct, but what is the reason for not spraying? In this case, it is necessary to carefully observe whether there is dirt at the contact surface of the nozzle. If so, clean up the dirt and the spray can be carried out normally. That‘s all we‘re going to talk about today. If you have any questions, follow us on facebook, Please feel free to ask us questions.
LED reflow oven for 3W high power LED E10 Main product: Reflow oven with 10 zones, hot air reflow oven, SMT equipment, PCB Assembly Equipment, PCB Assembly Equipment, SMD/SMT Assembly, SMT assembly line, automatic production line Heating System &
SMT Pneumatic Stencil Cleaning Machine If you could not find any similar items you want, you may send some photos to us. because our catalog and website haven't included all of our products. PCBA Cleaning Machine, On-line PCBA Cleaning Machine,
Career Center | DALLAS, Texas USA | Production
Extensive, diverse background in Production Management and Warehousing in state of the art manufacturing environments. Exceptional ability to translate corporate strategies and orchestrate between business components, resulting in deliverables on ti
Career Center | Shoubra Misr, Cairo, Egypt, Egypt | Engineering,Maintenance,Production,Quality Control
Refer to my CV
GPD Global | https://www.gpd-global.com/co_website/pdf/coating/SimpleCoat-Operation-Guide-23100600.pdf
differential switch Air flow sensor for the exhaust port. Stops pneumatics and gantry motion if flow drops below set point. 2. Indicators Machine status and error messages display in the main window and signal the user via the light tower. Connection status
