Full Site - : bad on (Page 2 of 13)

gold finish on pcbs

Electronics Forum | Thu Nov 09 23:27:53 EST 2000 | Craig

We are considering using gold plating on our fine pitch pcbs (as oppossed to HASL). We have heard of long term solder reliability problems with joint imbrittlment how bad is this and does it apply for all of the different plating processes the same?

Correction on misinformation

Electronics Forum | Tue Oct 09 14:41:13 EDT 2001 | mparker

I just realized my last posting has some incorrect references. Blame it on last nights sour mash! (St. Pauli girl didn't respond!) The article I referenced was found at the AlphaMetals website, a study done for AlledSignal, in conjunction with Churc

HASL on Pads

Electronics Forum | Mon Jun 14 11:44:23 EDT 2004 | Dreamsniper

I have boards with bad HASL application. First they're not even. Second some pad edges have no HASL and still remains bare copper. What's the maximum and minimum HASL thickness required for a good solderability. My boards are about 6 weeks old, I kno

Error on Fuji CP-3

Electronics Forum | Fri Apr 15 16:02:26 EDT 2005 | jdengler

ING, If my memory is correct: -This is from the large air cylinder below the X/Y table moving slow or not getting down all of the way. -The air cylinder has a sensor for when it's down all of the way. - This sensor could be bad but most of the t

Inconsistent mounting on TOPAZ-X

Electronics Forum | Fri Nov 14 17:37:58 EST 2008 | snsmt

WHat about bad mounting? i have 2 fixtures and sometimes it would mount with no misalignment and sometimes it would. WHat could be the problem in this case/ I know the fixtures are good because they work on a different program that we have. I don't u

feedback error on CSM84

Electronics Forum | Sun Dec 17 22:23:46 EST 2017 | jmelson

Well, I fixed it. I had resisted taking the motor off because of the recalibrations that would be required. But, it got bad enough I had to. Under the microscope, I could see copper dust packed between the commutator segments. I removed that, and

Paste drying on stencil

Electronics Forum | Tue Feb 11 14:37:26 EST 2020 | spoiltforchoice

If you're asking me, I'm using BLT LFS-UFP-T4 (they have an even better paste to treat badly now if you add zq). Those in the test of the world might find Loctite GC10 is similar, however the stencil and tack times on the BLT are pretty awesome and

no contact on BGA

Electronics Forum | Tue Jun 26 16:43:19 EDT 2001 | CPI

Yes a 6 mil solder deposite will reduce to approx 50% of it's original size. Does this happen on only 1 BGA? Is the BGA that its happening on have smaller balls than the others, what I'm getting to is, are you sure you are depositing the proper amo

Dewetting on QFP

Electronics Forum | Tue Jun 07 16:19:58 EDT 2005 | davef

Q1) How to identify on good or bad ICs lead that could contribute to dewetting? A1) Distinguish between good or bad IC that could contribute to dewetting by testing for solderability, according to J-STD-002. Q2) What actions that must be taken in fa

SMT on ceramic substrate

Electronics Forum | Wed Aug 22 21:11:25 EDT 2001 | davef

When it works right, it's a beautious thing. => When goes wrong, you have one board with some of the other board's material, not too coo. Scribed and broken ceramic has bad-butt sharp edges. You'll feel this sticky stuff on your hands, look down,


bad on searches for Companies, Equipment, Machines, Suppliers & Information

Count On Tools, Inc.
Count On Tools, Inc.

COT specializes in high quality SMT nozzles and consumables for pick and place machines. We provide special engineering design service of custom nozzles for those unique and odd components.

Manufacturer

2481 Hilton Drive
Gainesville, GA USA

Phone: (770) 538-0411

Sell Used SMT & Test Equipment

High Throughput Reflow Oven
Selective soldering solutions with Jade soldering machine

High Precision Fluid Dispensers
Best SMT Reflow Oven

World's Best Reflow Oven Customizable for Unique Applications
IPC Training & Certification - Blackfox

High Resolution Fast Speed Industrial Cameras.