Electronics Forum | Thu Oct 26 13:56:08 EDT 2000 | ptvianc
Hello: Pre-baking laminates should only be performed:(1) to meet contractual agreements or (2) in response to an actual defect that can be traced to PWB water absortion. Besides the fact that a pre-bake is an enormous process "bottleneck," it also
Electronics Forum | Fri Mar 26 03:25:02 EDT 2010 | grahamcooper22
HI, regarding the baking....why are you doing it every 72 hours ? How many times has each device been baked ? If you are worried about moisture in the devices the best policy is to store them correctly in dry packs or dry cabinets or bake them once j
Electronics Forum | Tue Jan 13 15:48:58 EST 2015 | natashakt
170 degrees Celsius) and regular FR4 materials. I am trying to see if we can use table 5 on page 14, "Recommended Equivalent Total Floor Life (Days)" to find out how long (at specific humidity and temperature) our populated and unpopulated PCB's can
Electronics Forum | Wed Apr 13 05:48:52 EDT 2005 | charly
hi' i need advise on immersion silver PCb shelf life. 1) what is the shelf life for Immersion silver PCB? 2) iF PCB expire, can we bake the immersion PCB? what temp & duration? 3) How long can we keep the pCB again after rebaking? (with vacuum seal)
Electronics Forum | Fri Jul 16 08:14:15 EDT 2010 | vetteboy86
We're expereincing issues in our pick and place machine due to what I consider a server warping of the PCB. The PCB is received this way from our PCB manufacturer. Before I push to much, I would like to know options for a cause. The warp is so bad,
Electronics Forum | Mon Mar 19 13:44:13 EDT 2012 | vinod
If PCB supplier has stored PCB in complete IPC specified storage condition and let say they kept for 2 Years. Are these PCB still good for use? I understand about shelf life and baking procedure but I am not sure how long PCB are good for use if they
Electronics Forum | Thu Dec 04 00:22:11 EST 2008 | maacolomer
Hi Steven, The 24 hrs bake is an overkill according with various J-STDs. Assuming a bake temperature over the 100 Celsius degrees. There are several factors to be considered before deciding the best methodology to wash misprinted board. However,
Electronics Forum | Wed Mar 29 04:14:49 EST 2000 | Marc
Charlie B: You mentioned that you have an air conditioned environment and a RH 0rf 50, baking the boards is predominately done when the history of the PCB delivery and / or previous storage conditions are un known. When I was with a CM, we did this a
Electronics Forum | Fri Jul 30 17:24:24 EDT 1999 | Dave F
| | Hello Netters, | | | | I have a customer who wants us to aquaeos wash a PCB after all operations have been performed. The PWB is two layer FR4 with a Transformer, a Multichip Module with Conformal Coating, (6) 11" insulated wires that are tinne
Electronics Forum | Wed Apr 06 04:18:03 EDT 2011 | emmanueldavid
TK, Hope you got it right only for this round of assemblies. Well, passing through a Reflow belt is not an ultimate process to dry circuit cards & take out moisture from Solder finished layers. First of all, if the packs were not unsealed (even s
Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.
Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
1750 Mitchell Ave.
Oroville, CA USA
Phone: (888) 406-2830
