Industry Directory | Consultant / Service Provider
Lead Conditioning, Lead Scanning, Tape & Reel, Lead Tinning, Bake & Dry-Pack, BGA Reballing Services
IDC is the developer of a low temperature baking process for removing moisture from moisture sensative package, while they remain in either tape or tubes. It is currently engineering equipment to support the process.
New Equipment | Education/Training
This course is designed for students that require the hands-on skill and knowledge to reliably remove and install many types of the most complex BGA components. Students are taught methods for safe and reliable BGA component rework using a top of the
The MSL baking process at OX3 Corporation, (�MSL� stands for Moisture Sensitivity Level), is in accordance with IPC and JEDEC Standard "J-STD-033A," the joint industry standard for semiconductor handling, packing, shipping and the use of moisture/ref
Electronics Forum | Mon Sep 20 16:06:53 EDT 2004 | blnorman
We require that the ovens used for bake out are vented, thus removing the vapor from the oven.
Electronics Forum | Wed Sep 15 22:44:58 EDT 2004 | pdeuel
RH changes with temprature. That's why your winshield de-fogs when your defroster is on.
Used SMT Equipment | SMT Equipment
Baking SMT on a cheap kitchen toaster oven is not difficult. You just need some patience and exploration good will. In this page you will read the manual procedure to bake SMD boards into a regular kitchen toaster oven appliance. Follows information
Industry News | 2010-09-13 15:36:15.0
IPC — Association Connecting Electronics Industries® has released IPC-1601, Printed Board Handling and Storage Guidelines. The industry's sole standard on the handling, packaging and storage of printed boards, IPC-1601 provides users with guidance on how to protect printed boards from contamination, physical damage, solderability degradation, electrostatic discharge and moisture uptake.
Industry News | 2018-10-18 08:32:52.0
How to Prevent Solder Ball and Bridging Defects during the SMT Reflow Process
Technical Library | 2021-11-26 14:34:07.0
The use of desiccant bags filled with Silica Sand and or Clay beads used in conjunction with a Moisture Barrier Bag to control moisture for storage of printed circuit boards has long been an accepted practice and standard from both JEDEC and IPC organizations. Additionally, the use heated ovens for baking off moisture using the evaporation process has also been a long#2;standing practice from these organizations. This paper on alternative drying methods will be accompanied by completed independent, unbiased tests conducted by Vinny Nguyen, an engineering student (now graduated) from San Jose State University. The accompanied paper will examine the performance levels of different technologies of desiccant bags to control moisture in enclosed spaces. The tests and equipment set were reviewed by an engineer and consultant to the Lockheed Martin Aerospace Division and the IPC - TM-650 2.6.28 test method was review by engineer from pSemi. The tests were designed to mimic performance tests outlined in Mil Spec 3464, which both IPC and JEDEC have adopted for their respective standards. The test examined variables including absorption capacity rates, weight gain and release of moisture back into the enclosed area. The presentation will also address and highlight: • Similarities of PCBs and Heavy Equipment as it applies to Inspections, Causes of Failure, Types of Corrosion and Moisture Collection Points. • Performance Attributes of Different Desiccant Technologies as it applies to shape, texture, change outs, labeling and regeneration. • Venn Diagram of Electromechanical Failure with the circles 1. Current 2. Contamination 3. Humidity Presentation Available
Technical Library | 2024-09-02 18:48:58.0
The conversion to higher temperature "Lead Free" assembly reflow conditions has created an increased awareness that entrapped or absorbed moisture is a frequent root cause of thermally induced delamination at assembly reflow. There are two connected failure modes from entrapped moisture; incomplete resin cross-linking resulting in premature resin decomposition and also severe Z axis expansion from "explosive vaporization of the entrapped moisture at elevated temperatures at assembly reflow". Ultimately, both result in delamination failure. Other papers have shown the negative effects of entrapped moisture before lamination including delamination, red color, reduced thermal reliability and increased high speed signal loss. In this paper, various materials were tested for moisture sensitivity during lamination. Tests were performed at varying lamination conditions including a pre-vacuum step and "kiss" step. Pressure and cure temperature parameters were evaluated for minimizing or eliminating the effect of trapped moisture. Also included are the results of inner layer moisture removal baking conditions and their effect on peel strength and thermal reliability.
Dennis Odonnell , Vice President of Precision PCB Services, Inc., Oroville CA Explains How to Evaluate a BGA Rework Station ! #BGA Rework Stations http://www.pcb-repair.com/bga-rework-station/
Dennis Odonnell , Vice President of Precision PCB Services, Inc., Oroville CA Explains How to Evaluate a BGA Rework Station ! #BGA Rework Stations http://www.pcb-repair.com/bga-rework-station/
Training Courses | | | PCB Rework and Hand Soldering Courses
The PCB rework and hand soldering courses courses cover techniques of rework and repair of PCBs, BGAs and other electronics assemblies, and teach fundamentals of soldering of electronics assemblies.
Training Courses | | | PCB Rework and Hand Soldering Courses
The PCB rework and hand soldering courses courses cover techniques of rework and repair of PCBs, BGAs and other electronics assemblies, and teach fundamentals of soldering of electronics assemblies.
Career Center | Theni, Tamilnadu India | Engineering
NPI Engineer: • Playing a role as NPI leader of the Telecom, Aerospace & Server Products to introduce and run to qualify the engineering build from customer. • Conducting Weekly NPI meeting with the CFT team to review the progress of the NPI schedu
Career Center | THRISSUR, India | Maintenance,Production
HANDLING OF MAINTENANCE Camelot,Mascot, Selective Soldering,Wave Soldering,Aquastorm 200,H-500 HI-Z,Kolb,kerry&PBT,GETECH, ATI 105 & Final Touch 101,Heller,Btu&vapour phase,Shuttle,SRT,ESD ,Electrical maintenance . Knowledge in using SLIM KIC 2000&
Precision PCB Services, Inc | https://precision-pcb-services-inc.com/products/bga-rework-training
. Circuit board preparation - masking, baking and other process steps. BGA site preparation. Solder mask breakdown - how to prevent it, how to fix it
| https://www.eptac.com/faqs/ask-helena-leo/ask/silver-immersion-finish-boards
. Baking will impact the solderability of the board, especially if they are as stated immersion silver boards. My recommendation is to assemble a board, bake it for at least 8 hours and process it through the wave solder process
winsouce.jpg)