Used SMT Equipment | AOI / Automated Optical Inspection
Description: Hello and thank you for your interest in our MVP AOI Machines For Sale.We have a total of (2)Ultra 18-20 MVP Automated Optical Inspection Machines,(1)CentOS based server. They were taken off line due to new machine installation would
Technical Library | 2023-06-02 14:13:02.0
This work examines the use of dual-material fused filament fabrication for 3D printing electronic componentsand circuits with conductive thermoplastic filaments. The resistivity of traces printed fromconductive thermoplastic filaments made with carbon-black, graphene, and copper as conductive fillerswas found to be 12, 0.78, and 0.014 ohm cm, respectively, enabling the creation of resistors with valuesspanning 3 orders of magnitude. The carbon black and graphene filaments were brittle and fracturedeasily, but the copper-based filament could be bent at least 500 times with little change in its resistance.Impedance measurements made on the thermoplastic filaments demonstrate that the copper-based filamenthad an impedance similar to a copper PCB trace at frequencies greater than 1 MHz. Dual material3D printing was used to fabricate a variety of inductors and capacitors with properties that could bepredictably tuned by modifying either the geometry of the components, or the materials used to fabricatethe components. These resistors, capacitors, and inductors were combined to create a fully 3Dprinted high-pass filter with properties comparable to its conventional counterparts. The relatively lowimpedance of the copper-based filament enabled its use for 3D printing of a receiver coil for wirelesspower transfer. We also demonstrate the ability to embed and connect surface mounted components in3D printed objects with a low-cost ($1000 in parts), open source dual-material 3D printer. This work thusdemonstrates the potential for FFF 3D printing to create complex, three-dimensional circuits composedof either embedded or fully-printed electronic components.
Automated 2D & 3D inspection Unsurpassed image quality High defect detection Low false calls Fast throughput Quick set-up Nordson YESTECH's versatile X3 Automated X-Ray Inspection Systems (AXI) offers complete inspection of sol
How to select a tip to be used with the HANDI-VAC and how to use the handivac. www.virtual-ii.com
A new task kit is available for LCR-Reader-MPA; the Professional. This bundle consists of and LCR-Reader-MPA, an NIST traceable calibration certificate, LCR-Reader Kelvin Probe Connector, spare bent tweezer tips, Offset Calibration Board, and chargin
The LineMaster Fusion is a revolutionary platform combining the best of ASC International’s 3D SPI sensor technology with its sophisticated image and algorithm based AOI sensor technology into a dual purpose, single source solution. Key Features & B
HANDI-VAC KIT, Static dissipative, with conductive silicone vacuum cups. (1) 1/8" and (1) 1/4" vacuum cups on bent probes and (1) 1/8" and (1) 3/8" vacuum cups on straight probes. Our HANDI-VAC kits are a low cost pick-and-place tool that can go in
PAC-VAC® vacuum tool kit, battery operated. The PAC-VAC® is battery operated and self-contained, runs up to eight hours continuously on one 9 volt alkaline battery. This versatile unit can be clipped to your belt or pocket for one-handed portable ope
New Equipment | Assembly Services
We have a used GSM 2 dual beam Flex Jet 7 We are currently using the beam 2 head. Only 6 spindles currently being used (spindle 5 is slightly bent we opted not to use it) beam 1 has a damaged touchdown sensor witch I believe all that information is
New Equipment | Test Equipment
A new task kit is available for LCR-Reader-MPA; the Professional. This bundle consists of and LCR-Reader-MPA, an NIST traceable calibration certificate, LCR-Reader Kelvin Probe Connector, spare bent tweezer tips, Offset Calibration Board, and chargin
