Industry News | 2021-12-27 20:17:56.0
The lubricating oil used in a refrigeration compressors can lubricate the friction surface, reduce the friction work, friction heat and avoid wear of the compressor motor. Besides, filling the sealing part with oil can ensure its performance and prevent the leakage of refrigerant. Here are four reasons why the oil of refrigeration compressor deteriorate.
Industry News | 2009-02-11 23:22:16.0
ndium8.9HF Solder Paste is a halogen-free Pb-free solder paste with unsurpassed print transfer efficiency and response-to-pause printing. The advanced rheology of Indium8.9HF is ideally suited for today's advanced 0.4mm pitch and 0201 technologies.
Industry News | 2018-01-16 11:59:10.0
Vision Engineering has teamed up with industry-expert Bob Willis to broadcast a free Electronics Academy Webinar aimed at identifying the issues affecting PCB/SMT assembly and the challenges of achieving Zero Defect Manufacture. The next webinar, Eliminate Printed Circuit Board Problems & Failure Modes will take place on January 23rd at 2:30 EST.
A technology that identifies the intermetallic compound formation, enables the system to provide closed loop feedback to the operator and validates the condition of the solder joint. This technology works in conjunction with SmartHeat® and patented C
Industry News | 2018-10-18 08:04:17.0
Influences of the solder material for the wave soldering machine soldering quality
Industry News | 2018-10-18 08:05:54.0
The benefits of hard oxidation treatment of wave soldering mahcine and reflow oven guide Rail
Industry News | 2011-02-14 14:35:18.0
Christopher Associates/Koki Solder announces that Jasbir Bath, Consulting Engineer, will give a presentation about Head-in-Pillow Component Soldering Defects at the upcoming LA/O.C. SMTA Chapter Dinner, scheduled to take place Thursday, February 17, 2011 at JT Schmid’s Restaurant & Brewery in Anaheim, CA at 7 p.m.
Industry News | 2018-11-27 14:03:14.0
Super PCB is pleased to announce that it offers a variety of quality PCB surface finishes. PCB surface finish is the coating between the PCB and components that provides a solderable surface for components and protects the exposed copper circuitry.
New Equipment | Board Handling - Storage
Eureka TUS-501 Fast Super Dryer Dry Cabinet Specs: http://eurekadrytech.com/fast-super-dryer/tus-501 Model: TUS-501 Fast Super Dryer Capacity: 372 Liters Humidity Range: 10%-50% Recovery Time: Recovers to ≤ 20% RH within 2 hours after accessing doo
Technical Library | 2021-11-03 16:52:47.0
This paper proposes the integration of pulsed photonic sintering into multi-material additive manufacturing processes in order to produce multifunctional components that would be nearly impossible to produce any other way. Pulsed photonic curing uses high power Xenon flash lamps to thermally fuse printed nanomaterials such as conductive metal inks. To determine the feasibility of the proposed integration, three different polymer additive manufacturing materials were exposed to typical flash curing conditions using a Novacentrix Pulseforge 3300 system. FTIR analysis revealed virtually no change in the polymer substrates, thus indicating that the curing energy did not damage the polymer. Next, copper traces were printed on the same substrate, dried, and photonically cured to establish the feasibility of thermally fusing copper metal on the polymer additive manufacturing substrates. Although drying defects were observed, electrical resistivity values ranging from 0.081 to 0.103 Ω/sq. indicated that high temperature and easily oxidized metals can be successfully printed and cured on several commonly used polymer additive manufacturing materials. These results indicate that pulsed photonic curing holds tremendous promise as an enabling technology for next generation multimaterial additive manufacturing processes.
.png)
